PDA

View Full Version : TIPS ON CAR PAINTING.. kahit anong tanong ukol sa pagpipintura ng car or motorcycle



Pages : 1 [2] 3 4 5 6 7 8 9 10 11 12 13

solo_baric
28th Oct 2011, 14:24
bale, yung catalyst lang ang idadagdag sa urethane?tapos may thinner pa? pag hindi tama ang mixture ng catalyst at thinner, malamang sabotahe ang trabaho.


oo, yun nga. di naman ganun kadelikado, tanchahan din ang mix ng catalyst niya. di lang talaga pwedeng madaliin ang urethane. dun sya masisira pagka inagad ang trabaho. patience ang kailangan.

JRsixten
28th Oct 2011, 22:01
nice thread po! sir tnong q lng kung anong magandang paint para sa motor q na hindi matutuklap ska hindi bumubukol saka ano po tips nyo para maganda ung paglagay ng pintura honda xrm 125 po:pray:

original paba ung pintora nyan oh na pintorahan na?..

advice ko lng..

lihain munang mabuti,,, at gamiting mong primer ay ung plastic primer.. at mas maganda kong al color lng ung mga plastic nyan...
urathane gamitin mo para makintab..

acrylic - makintab pagkatapos at pagkatapos ng isang linggo.. walang kintab na yan..

urethane - 3 years and up ang kintab nyan.. dependi sa alaga...

good urethane brand na nagamit ko...
top.
1.nippon
2.anzhal
3.weber
4.pollygloss

solo_baric
28th Oct 2011, 22:49
anzhal brand

trusted na at kilala sa urethane paint.

kylenatan
29th Oct 2011, 17:21
tnx sir solo baric,nilalagyan pba ng primer yun bago acrylic?

solo_baric
29th Oct 2011, 20:58
tnx sir solo baric,nilalagyan pba ng primer yun bago acrylic?


kung may pintura na at papatungan na lang, hindi na gagamitan ng primer. diretso na sa kulay. kung may masilya or labas ang lata o plastic, primer muna saka i paint ang color and then top coat para maging glossy.

:welcome:

JRsixten
30th Oct 2011, 17:33
tnx sir solo baric,nilalagyan pba ng primer yun bago acrylic?


kung may pintura na at papatungan na lang, hindi na gagamitan ng primer. diretso na sa kulay. kung may masilya or labas ang lata o plastic, primer muna saka i paint ang color and then top coat para maging glossy.

:welcome:[/QUOTE]

at depende den po sa kulay na i pipintura mo... meron kasing pintora kailngan may eh under coat at meron ding hindi na kaylangan may undercoat..

solo_baric
31st Oct 2011, 05:01
at depende den po sa kulay na i pipintura mo... meron kasing pintora kailngan may eh under coat at meron ding hindi na kaylangan may undercoat..

tama ka, tulad ng red colors, matagal tumakip lalo na mga candy tone.
kaya kailangan may pondong kulay. karaniwan kapag red colors, popondohan ng white bago kulay.

JRsixten
31st Oct 2011, 23:35
tama ka, tulad ng red colors, matagal tumakip lalo na mga candy tone.
kaya kailangan may pondong kulay. karaniwan kapag red colors, popondohan ng white bago kulay.

and also yellow tol :beat:

solo_baric
1st Nov 2011, 07:29
Here is a list of the paint makers ..

PPG - the have the Vibrance Collection- can get it most every where..

Dupont - the makers of the most used oem stock colors like viper red

Valspar - the makers of debeers paint most body use them as well.. NOTE you will notice that on the site you will see link heading towards house of kolor paints they are the owners and bought the right to the paint but they were not the inverters

House of Kolor - The first maker to introduce the "candy" lines of paint. lots of choices and you can get it in small amounts

Auto Air Colors- the makers of a water based painting system

Alsa corp - the makers of the true off the wall paints from the chrome , to ghost chrome , hyper color paints" remember the 80's body glove shirts" way to much to list but it worth to check into

Collusus11
3rd Nov 2011, 00:51
[QUOTE=Collusus11;8164965]

2 kasi alam kong process ng carbon fiber:

1st > carbon fiber sheet, ilalatag at ididikit na lang sa part ng car.
2nd > through air brush.




salamat TS...malaking bagay itong advice mo na ito :clap: :clap: :clap:

solo_baric
3rd Nov 2011, 08:50
[QUOTE=Collusus11;8164965]

2 kasi alam kong process ng carbon fiber:

1st > carbon fiber sheet, ilalatag at ididikit na lang sa part ng car.
2nd > through air brush.




salamat TS...malaking bagay itong advice mo na ito :clap: :clap: :clap:

walang anuman sir.

:welcome:

gandoose
4th Nov 2011, 10:52
laking tulong ng thread , buti may nakaisip na gwin ito saludo ako sa yo bosing, isa kanghenyo...:salute:

solo_baric
4th Nov 2011, 21:43
laking tulong ng thread , buti may nakaisip na gwin ito saludo ako sa yo bosing, isa kanghenyo...:salute:


thanks sir gandoose. gusto ko lang naman i share ang nalalaman ko sa iba para makatulong.

royski
5th Nov 2011, 04:32
Bookmark muna ako TS...matagal ko ng hinahanap ang mga ganitong thread tungkol sa car painting, may mga tanong din ako, pero later na lang, maraming salamat brader sa pag-start ng thread na ito...good luck at God Bless...

deftechguy
5th Nov 2011, 04:53
sir, may shop po ba kau? san po ang location,thanks!

solo_baric
5th Nov 2011, 06:55
Bookmark muna ako TS...matagal ko ng hinahanap ang mga ganitong thread tungkol sa car painting, may mga tanong din ako, pero later na lang, maraming salamat brader sa pag-start ng thread na ito...good luck at God Bless...

welcome sir and thanks too.

:welcome:


sir, may shop po ba kau? san po ang location,thanks!

wala kaming shop, home service lang at nakapag trabaho din ako sa 2 casa (HINO MOTORS & DIAMOND MOTORS MITSUBISHI).

my brother is also a car painter and color technician in a company in QC.

:welcome:

george10
7th Nov 2011, 17:09
:help:sir ask ko lng po sa plastic anung pintura ba ang dapat gamitin pang MC. kasi eh! tnx boss in advance:help:

solo_baric
7th Nov 2011, 21:24
:help:sir ask ko lng po sa plastic anung pintura ba ang dapat gamitin pang MC. kasi eh! tnx boss in advance:help:


karaniwan, acrylic paint din ang pwedeng gamitin. pero kung wala pang pintura yung plastic parts na pipinturahan, mas maganda na gamitan mo siya ng plastic primer paint bago ipintura ang kulay at top coat.

kung wala kang mabiling plastic primer, pwede ring epoxy primer ang gamitin, pero mas kakapit sa plastic yung plastic primer.

:welcome:

deftechguy
10th Nov 2011, 02:07
sakali,pwedeng papinturahan ang amplifier? vintage kc yung nabili ko and balak kong pahilamusan ung ibabaw and gilid..magkano kaya ang aabutin? saka ung location ninyo sakali...thanks

You can see links before reply

solo_baric
10th Nov 2011, 07:36
sakali,pwedeng papinturahan ang amplifier? vintage kc yung nabili ko and balak kong pahilamusan ung ibabaw and gilid..magkano kaya ang aabutin? saka ung location ninyo sakali...thanks

You can see links before reply


pwede tol, baklasin mo yung takip sa ibabaw at gilid saka mo pinturahan. dapat the same ang kulay na gamitin para ma restore ang original look. acrylic na gamitin mo para matibay at pwedeng timplahin ang kulay kapareho ng color ng amplifier mo.

malayo location ko, tarlac ang base ko ngayon. hanap ka na lang ng well experienced na pintor sa area mo.

about price, hindi aabutin ng P500 yan kung papipinturahan mo sa pintor. tip ko sa'yo sa pintor ng kotse mo papinturahan, mas pulido at metikuloso sila magpintura.

deftechguy
10th Nov 2011, 21:10
Salamat ng marami sa info pati sa presyo. Plus 1 sa thread na ito

iamjokerinland
10th Nov 2011, 21:39
nice thread ts lapit ako sayo pagka gusto kong palitan kulay ng otto ko

solo_baric
10th Nov 2011, 23:00
Salamat ng marami sa info pati sa presyo. Plus 1 sa thread na ito

you're welcome bro.

:welcome:


nice thread ts lapit ako sayo pagka gusto kong palitan kulay ng otto ko

anytime sir.
willing to share some advise para di tayo malamangan ng iba.

dnzkram
10th Nov 2011, 23:38
sir, may alam ka bang mas madali na way para ma strip ang paint ng mga mag wheels? yung stripsol kasi di rin masyado maalis yung color gray na parang expoxy primer sa oem painted wheels. need ko pa steel brush minsan para maalis. thanks po

solo_baric
13th Nov 2011, 10:02
sir, may alam ka bang mas madali na way para ma strip ang paint ng mga mag wheels? yung stripsol kasi di rin masyado maalis yung color gray na parang expoxy primer sa oem painted wheels. need ko pa steel brush minsan para maalis. thanks po

yan na ang pinaka madaling process para matanggal ang paint. yung gray color na paint sa mags, talagang makapit yan. pahiran mo lang ng stripsol, tapos mga 3-5 minutes, remove paint gamit ang spatula or paleta. kung may matira pa, pahiran uli ng stripsol then the same procedure ule.


mukhang fans ka rin ng kicker. :lol:

farfarah
13th Nov 2011, 10:24
sir ganto gusto kong kulay sa motor ko eh ano po bang kulay to?
salamat..:thumbsup:

magkano po kaya ganyan kulay sa motor..
salamat ulit..

You can see links before reply

menggoy
15th Nov 2011, 05:36
sir, pano diskarte dito bago ko pinturahan? masyadong lowered dati kaya naging ganyan.

You can see links before reply
You can see links before reply
You can see links before reply
You can see links before reply

paano ang best way para matanggal ang crack bago masilyahan? yung tipong kapit na kapit ang masilya para di na ulit basta basta magcrack.

solo_baric
15th Nov 2011, 09:09
sir, pano diskarte dito bago ko pinturahan? masyadong lowered dati kaya naging ganyan.

You can see links before reply
You can see links before reply
You can see links before reply
You can see links before reply

paano ang best way para matanggal ang crack bago masilyahan? yung tipong kapit na kapit ang masilya para di na ulit basta basta magcrack.

lahat ng may bitak, i strip mo hanggang ilalim. kung may bitak na ang mismong spoiler, gamitan mo siya ng epoxy contact cement (yung ginagamit sa mga bangka). pagkatapos masilyahan mo.


sir ganto gusto kong kulay sa motor ko eh ano po bang kulay to?
salamat..:thumbsup:

magkano po kaya ganyan kulay sa motor..
salamat ulit..

You can see links before reply

maraming klase ng ganyang color. ang isa sa malapit lapit dyan ay yung CANDY APPLE RED

menggoy
15th Nov 2011, 16:24
lahat ng may bitak, i strip mo hanggang ilalim. kung may bitak na ang mismong spoiler, gamitan mo siya ng epoxy contact cement (yung ginagamit sa mga bangka). pagkatapos masilyahan mo.


ipapapahid lang ba yung epoxy contact cement? saan po nakakabili nito?

solo_baric
16th Nov 2011, 08:49
ipapapahid lang ba yung epoxy contact cement? saan po nakakabili nito?

sa mga hardware meron nyan. 2 piraso yan pag bumili ka, yung isa hardener yun. mabilis dapat i apply kasi medyo mabilis matuyo.

menggoy
16th Nov 2011, 14:15
pwede bang igrinder ko na lang yung mga bitak para mabilis matanggal sabay pahid ng epoxy contact cement?

dnzkram
17th Nov 2011, 10:25
yan na ang pinaka madaling process para matanggal ang paint. yung gray color na paint sa mags, talagang makapit yan. pahiran mo lang ng stripsol, tapos mga 3-5 minutes, remove paint gamit ang spatula or paleta. kung may matira pa, pahiran uli ng stripsol then the same procedure ule.


mukhang fans ka rin ng kicker. :lol:

nyay! un na pala pinaka madali proseso hehe.. nahihirapan pako mejo madugo kc sir hehe... yes sir dati ako user ng 2pcs 15" solo baric dual 2 ohms sa beetle ko. nag shift nako sa RE ngayon sir hehe.. thanks sa reply! more power! galing nitong thread na to very informative :dance:

dnzkram
17th Nov 2011, 10:28
balak ko sana pinturahan yung trunk ng lancer ko. pano kaya tatakpan yung mga butas na pinanggalingan ng spoiler? pwede bang epoxy na lang instead of welding? ano kayang magandang epoxy bibilhin ko nun sir? tska pano procedure ng pag epoxy? hehe thanks!

yung butas sir siguro mga 8mm radius

solo_baric
18th Nov 2011, 10:04
pwede bang igrinder ko na lang yung mga bitak para mabilis matanggal sabay pahid ng epoxy contact cement?

Pwede tol, pero alalay lang baka maupod pati fiber glass. lalong lalaki sira.


nyay! un na pala pinaka madali proseso hehe.. nahihirapan pako mejo madugo kc sir hehe... yes sir dati ako user ng 2pcs 15" solo baric dual 2 ohms sa beetle ko. nag shift nako sa RE ngayon sir hehe.. thanks sa reply! more power! galing nitong thread na to very informative :dance:

welcome tol. kicker user din ako.


balak ko sana pinturahan yung trunk ng lancer ko. pano kaya tatakpan yung mga butas na pinanggalingan ng spoiler? pwede bang epoxy na lang instead of welding? ano kayang magandang epoxy bibilhin ko nun sir? tska pano procedure ng pag epoxy? hehe thanks!

yung butas sir siguro mga 8mm radius

Oo, pwede epoxy, pwede nga rin masilya pero mas matibay ang epoxy. Bilhin mong epoxy yung non-sag, ginagamit yan sa bangka kaya mas matibay compare sa ibang epoxy.

may katulad nito na naka sachet lang

You can see links before reply

kung maramihan, ganito bilhin mo.

You can see links before reply

mix mo lang yung epoxy at hardener saka i apply sa hole.

dnzkram
18th Nov 2011, 16:44
:dance: woohoo! galing nitong thread na to! thanks bro! :yipee:

solo_baric
19th Nov 2011, 09:24
:dance: woohoo! galing nitong thread na to! thanks bro! :yipee:

welcome sir.

:welcome:

rukawa11
22nd Nov 2011, 08:31
sir ganda ng thread mo..may question sana ako

1. diba ung carbon fiber na nilalagay sa hood eh sticker..diba madali lang magasgasan yun.pagnagasgasan na eh pangit na. blak ko kasi lagyan ng black yun hood ng civic kc medyo kupas na un color and prang bitak na un kulay.ano ba maganda ts na ilagay un carbon fiber or papatungan nlang ng color. pag pinatungan ba ng color magkano aabutin ksama na pagawa ??

2. den ts un bubong ng civic naman me bula bula na rin. mga lima na malalaki ang bula. kung papaaus din un ts magkano rin pagawa. gusto ko kc mlaman kun magkano pagawa nun bka kc maloko ako sa presyo..

jigsgfx
22nd Nov 2011, 19:42
sir TS ask lang kasi my minor scratch ung motmot qo hmmm mwawala b sya kung sprayan qo ng clear? and ok lang b kung sprayan ko kahit my sticker pang top coat pra d mdaling mabakbak ung sticker?

thanks in advance

solo_baric
22nd Nov 2011, 22:02
sir ganda ng thread mo..may question sana ako

1. diba ung carbon fiber na nilalagay sa hood eh sticker..diba madali lang magasgasan yun.pagnagasgasan na eh pangit na. blak ko kasi lagyan ng black yun hood ng civic kc medyo kupas na un color and prang bitak na un kulay.ano ba maganda ts na ilagay un carbon fiber or papatungan nlang ng color. pag pinatungan ba ng color magkano aabutin ksama na pagawa ??

maraming klase ng carbon fiber:

1. mayroong carbon fiber vinyl with or non adhesive siya kaya para talaga siyang sticker, tulad nito.

You can see links before reply

2. mayroon namang paint tricks lang. proseso ng painting na magiging carbon fiber finished.

You can see links before reply

ginagamitan ito ng mat shelf liner.

You can see links before reply

kung gusto mo maporma, maganda yang carbon fiber. yun nga lang may kamahalan ang magpalagay nito pati materyales. kung DIY, kailangan may mag guide sayo na may experienced sa paglalagay ng carbon fiber. kung papipinturahan mo lang at kung hood lang, siguro mga 7hundred to 1 thousand ang magagastos, depende sa pintor na makukuha mo.

2. den ts un bubong ng civic naman me bula bula na rin. mga lima na malalaki ang bula. kung papaaus din un ts magkano rin pagawa. gusto ko kc mlaman kun magkano pagawa nun bka kc maloko ako sa presyo..

usually kapag malaki ang bula, malamang butas na ang lata o kinain na ng kalawang, maaari din dahil hindi kumapit yung pintura sa lata o masilya.

kung bubong lang ang pipinturahan ang price niya mga nasa 1500-2000. kung may butas na yung lata kailangan ipalatero, mas mataas na singil dahil babayaran mo pati latero at depende rin sa dami ng butas.


sir TS ask lang kasi my minor scratch ung motmot qo hmmm mwawala b sya kung sprayan qo ng clear? and ok lang b kung sprayan ko kahit my sticker pang top coat pra d mdaling mabakbak ung sticker?

thanks in advance

kung mababaw lang ang scratch, maaaring matakpan ng clear, kung malalim, hindi siya mawawala, dapat at masilyahan na at pinturahan.

pwedeng patungan ng clear ang sticker pero hindi gaanong kakapit ang clear sa sticker dahil malambot at flexi ito. kaya mas advisable na hindi dapat patungan ng pintura o clear ang sticker.

gamitin mong sticker yung talagang durable. para kahit hindi pinturahan ay hindi matatanggal agad.

KONOG
22nd Nov 2011, 22:39
sir ano pong masasabi niyo sa brand na Guilder?

rukawa11
23rd Nov 2011, 07:24
usually kapag malaki ang bula, malamang butas na ang lata o kinain na ng kalawang, maaari din dahil hindi kumapit yung pintura sa lata o masilya.

kung bubong lang ang pipinturahan ang price niya mga nasa 1500-2000. kung may butas na yung lata kailangan ipalatero, mas mataas na singil dahil babayaran mo pati latero at depende rin sa dami ng butas.



kung mababaw lang ang scratch, maaaring matakpan ng clear, kung malalim, hindi siya mawawala, dapat at masilyahan na at pinturahan.

pwedeng patungan ng clear ang sticker pero hindi gaanong kakapit ang clear sa sticker dahil malambot at flexi ito. kaya mas advisable na hindi dapat patungan ng pintura o clear ang sticker.

gamitin mong sticker yung talagang durable. para kahit hindi pinturahan ay hindi matatanggal agad.

ts maraming tnx ha..laking tulong ng thread mo... god bless

solo_baric
23rd Nov 2011, 13:38
sir ano pong masasabi niyo sa brand na Guilder?

Sa mga pintor, nasa mid class ang brand na GUILDER. Kung hindi ka maselan, pwede na ang brand na yan. Kung gusto mo ng mas quality at durable, kung may budget din lang, RM brand na or the same level price ang bilhin.


ts maraming tnx ha..laking tulong ng thread mo... god bless

you're welcome sir.

:welcome:

hgalcayde
23rd Nov 2011, 21:51
thumbs up sir :thumbsup:,..nice thread:salute:,..kahit walei aq sasakyan n ppinturahan eh,..halata sa mga post mo n sincere k at willing k makatulong,..salamat :clap: :dance: :praise:

imba_kan
23rd Nov 2011, 22:31
subscribe muna ts hehhe

solo_baric
24th Nov 2011, 06:19
thumbs up sir :thumbsup:,..nice thread:salute:,..kahit walei aq sasakyan n ppinturahan eh,..halata sa mga post mo n sincere k at willing k makatulong,..salamat :clap: :dance: :praise:

thanks. sure, i'm willing to share my gift to others. :thumbsup:


subscribe muna ts hehhe

welcome here site mate.

:welcome:

rukawa11
24th Nov 2011, 07:29
sir ts paisang tanung pa po..bago lang kc kmi s sasakyan eh..pano po ba mag maintain ng sasakyan..hmmmm ano ba gawin na maintenance s 1 month 6 months 1 yir.....tuwing kelan pti pa tune up and anu ba mga oil na nilalagay at kelan.. bka kc mabulok un sasakyan dto.. dpa kc kmi nakakakuha ng non pro..tnx sa advance sir...

solo_baric
24th Nov 2011, 13:19
sir ts paisang tanung pa po..bago lang kc kmi s sasakyan eh..pano po ba mag maintain ng sasakyan..hmmmm ano ba gawin na maintenance s 1 month 6 months 1 yir.....tuwing kelan pti pa tune up and anu ba mga oil na nilalagay at kelan.. bka kc mabulok un sasakyan dto.. dpa kc kmi nakakakuha ng non pro..tnx sa advance sir...

sa makina, wala akong alam gaano sa pag maintain.

sa pintura, para ma maintain ang ganda ng pintura lalo pa nga at brand new. dapat laging naka silong, direct sunlight ang malakas maka fade ng pintura. mas maganda nga may kulambo pa.

kung ipapa washing, iwasang gumamit ng sabon, dapat tubig lang. pagkatapos ipawashing, punasan ang buong car, lalo na ang mga ilalim kung saan nagpopondo ang tubig, doon nagmumula ang kalawang. pranela ang gamiting basahan, malambot kasi yon ipunas sa car at hindi gagasgas sa pintura.

ito pa ang mga karagdagan, english nga lang:

Wash your car regularly - I'd recommend to do this at least once a month. Things like bugs, bird's dropping, or limestone dripping damage the paint leaving permanent stains if not washed off in time.
In winter time, the chrome wheels and other chrome trim parts could be damaged by corrosion if the vehicle is not washed after driving on the roads when the salt was used. When the car is clean, all the moisture dries up quickly, but when it's dirty, the moisture accumulates in dirty areas causing corrosion.

You can see links before reply

At least once in a while use a pressure wash - you can find a pressure wash at self-service coin car wash stations. The pressure was removes the dirt from difficult to reach areas. Don't hold the pressure wash jet too close to the painted surfaces, it can peel off a loose paint. Wash off all the places where the dirt and salt could be accumulated; for example, behind moldings, inside wheel arches, under the bumpers, etc. It's particularly helpful after winter season - to wash out all the salt accumulations that speed up the corrosion process.

Don't forget to wash all the dirt from the windshield. The sand that left out on the windshield gets caught by the windshield wipers blades and scratches the windshield when the wipers are operating. Regularly clean the leaves and other debris from the areas below the windshield and the water channels under the hood and trunk, as the leaves block the water drains and collect the moisture, speeding up the corrosion process and causing a damp smell inside your car.

You can see links before reply

Wax your car regularly. A car wax gives shiny look to your car and helps to shield the paint from harsh environment, protecting it from fading. It takes only about 30 minutes to wax a whole car and high-quality car wax stays on the car for three - four months. So far, I haven't seen a single product that stays for life time as you may have heard in some commercials - nothing lasts forever. In order to maintain protective coat any product needs to be reapplied periodically.

You can see links before reply

How to clean bird droppings:
Bird droppings are very acidic and abrasive. The best way to clean the bird droppings off is to first soak them with water (few drops of soap, if available, will also help) for a few minutes and then just spray them off. The stains left from bird droppings can be buffed off with the fine polishing compound and then covered with car wax. If birds target your car regularly it might be a good idea to keep a spray bottle with water in your car, so you can wash the bird droppings off before they cause stains.

Undercoating and rustproofing your vehicle:
If you live in an area with high humidity, or where the salt use is common in winter months, undercoating and rustproofing can help to protect the car body and chassis components of your car from corrosion. Look at the picture, this is a proportioning valve, part of the brake system. It's located underneath the car and as you can see, it's completely rusted, even though this vehicle is only five years old. This happened because this vehicle was driven in a "rust belt" area with high humidity and lots of salt on the roads in winter. Sometimes later, one of these brake lines can burst and the car will have no brakes.
Properly done undercoating and rustproofing can protect important components of the car from corrosion.

You can see links before reply

How to repair stone chips:
The stone chips if not repaired in time will cause corrosion like in the first photo. That's why it's good idea to repair stone chips as soon as they appear. This one, near the headlight in the second photo is not corroded yet, so I'll try to repair it. The car is clean and dry and I have all I need: the matching spray paint ordered from a dealer and a sharp wooden stick (a toothpick will work as well). After shaking the spray paint very well for a few minutes, I spray very small amount into the cap. Now, I dip the end of the stick into the paint in the cap.

You can see links before reply

First, I'm trying to repair another stone chip in a less visible area to practice. Very carefully, I'm trying to barely fill up the chip without letting the paint to come out. It works. Now I'm doing the same with the chip near the headlight. Now it looks much better and it won't be corroded.

You can see links before reply You can see links before reply

How to remove paint marks left by other objects:
This mark on the door was made on the parking lot when someone opened the door a bit too wide. If you look very closely it's actually green paint residue over original clearcoat. The clearcoat itself seems to be damaged only slightly. I'll try to remove this mark. All I need for this is ultra-fine 1500-grit or 2000-grit waterproof sandpaper (the higher number stands for the finest abrasive), polishing compound containing mild abrasive (I used the Turtle Wax) and a car wax. Very carefully (I don't want to remove the clearcoat) I sand the marks with wet sandpaper (use only ultra-fine waterproof sandpaper) until all marks are gone. If you have never done it before, try on some small spot to see how it works first.

You can see links before reply You can see links before reply You can see links before reply

Now there is no mark, but the clearcoat has lost its shine; I will use polishing compound to make it shiny again. I put small amount of the polishing compound onto the damp sponge and rub well until the clearcoat becomes shiny again.

You can see links before reply You can see links before reply You can see links before reply

Last step, I wash out all the polishing compound and buff the area with the car wax. Now, all that's left from the paint mark is a barely visible dent.

You can see links before reply You can see links before reply You can see links before reply

rukawa11
24th Nov 2011, 15:22
sa makina, wala akong alam gaano sa pag maintain.

sa pintura, para ma maintain ang ganda ng pintura lalo pa nga at brand new. dapat laging naka silong, direct sunlight ang malakas maka fade ng pintura. mas maganda nga may kulambo pa.

kung ipapa washing, iwasang gumamit ng sabon, dapat tubig lang. pagkatapos ipawashing, punasan ang buong car, lalo na ang mga ilalim kung saan nagpopondo ang tubig, doon nagmumula ang kalawang. pranela ang gamiting basahan, malambot kasi yon ipunas sa car at hindi gagasgas sa pintura.

ito pa ang mga karagdagan, english nga lang:

Wash your car regularly - I'd recommend to do this at least once a month. Things like bugs, bird's dropping, or limestone dripping damage the paint leaving permanent stains if not washed off in time.
In winter time, the chrome wheels and other chrome trim parts could be damaged by corrosion if the vehicle is not washed after driving on the roads when the salt was used. When the car is clean, all the moisture dries up quickly, but when it's dirty, the moisture accumulates in dirty areas causing corrosion.

You can see links before reply

At least once in a while use a pressure wash - you can find a pressure wash at self-service coin car wash stations. The pressure was removes the dirt from difficult to reach areas. Don't hold the pressure wash jet too close to the painted surfaces, it can peel off a loose paint. Wash off all the places where the dirt and salt could be accumulated; for example, behind moldings, inside wheel arches, under the bumpers, etc. It's particularly helpful after winter season - to wash out all the salt accumulations that speed up the corrosion process.

Don't forget to wash all the dirt from the windshield. The sand that left out on the windshield gets caught by the windshield wipers blades and scratches the windshield when the wipers are operating. Regularly clean the leaves and other debris from the areas below the windshield and the water channels under the hood and trunk, as the leaves block the water drains and collect the moisture, speeding up the corrosion process and causing a damp smell inside your car.

You can see links before reply

Wax your car regularly. A car wax gives shiny look to your car and helps to shield the paint from harsh environment, protecting it from fading. It takes only about 30 minutes to wax a whole car and high-quality car wax stays on the car for three - four months. So far, I haven't seen a single product that stays for life time as you may have heard in some commercials - nothing lasts forever. In order to maintain protective coat any product needs to be reapplied periodically.

You can see links before reply

How to clean bird droppings:
Bird droppings are very acidic and abrasive. The best way to clean the bird droppings off is to first soak them with water (few drops of soap, if available, will also help) for a few minutes and then just spray them off. The stains left from bird droppings can be buffed off with the fine polishing compound and then covered with car wax. If birds target your car regularly it might be a good idea to keep a spray bottle with water in your car, so you can wash the bird droppings off before they cause stains.

Undercoating and rustproofing your vehicle:
If you live in an area with high humidity, or where the salt use is common in winter months, undercoating and rustproofing can help to protect the car body and chassis components of your car from corrosion. Look at the picture, this is a proportioning valve, part of the brake system. It's located underneath the car and as you can see, it's completely rusted, even though this vehicle is only five years old. This happened because this vehicle was driven in a "rust belt" area with high humidity and lots of salt on the roads in winter. Sometimes later, one of these brake lines can burst and the car will have no brakes.
Properly done undercoating and rustproofing can protect important components of the car from corrosion.

You can see links before reply

How to repair stone chips:
The stone chips if not repaired in time will cause corrosion like in the first photo. That's why it's good idea to repair stone chips as soon as they appear. This one, near the headlight in the second photo is not corroded yet, so I'll try to repair it. The car is clean and dry and I have all I need: the matching spray paint ordered from a dealer and a sharp wooden stick (a toothpick will work as well). After shaking the spray paint very well for a few minutes, I spray very small amount into the cap. Now, I dip the end of the stick into the paint in the cap.

You can see links before reply

First, I'm trying to repair another stone chip in a less visible area to practice. Very carefully, I'm trying to barely fill up the chip without letting the paint to come out. It works. Now I'm doing the same with the chip near the headlight. Now it looks much better and it won't be corroded.

You can see links before reply You can see links before reply

How to remove paint marks left by other objects:
This mark on the door was made on the parking lot when someone opened the door a bit too wide. If you look very closely it's actually green paint residue over original clearcoat. The clearcoat itself seems to be damaged only slightly. I'll try to remove this mark. All I need for this is ultra-fine 1500-grit or 2000-grit waterproof sandpaper (the higher number stands for the finest abrasive), polishing compound containing mild abrasive (I used the Turtle Wax) and a car wax. Very carefully (I don't want to remove the clearcoat) I sand the marks with wet sandpaper (use only ultra-fine waterproof sandpaper) until all marks are gone. If you have never done it before, try on some small spot to see how it works first.

You can see links before reply You can see links before reply You can see links before reply

Now there is no mark, but the clearcoat has lost its shine; I will use polishing compound to make it shiny again. I put small amount of the polishing compound onto the damp sponge and rub well until the clearcoat becomes shiny again.

You can see links before reply You can see links before reply You can see links before reply

Last step, I wash out all the polishing compound and buff the area with the car wax. Now, all that's left from the paint mark is a barely visible dent.

You can see links before reply You can see links before reply You can see links before reply

ah ok..ts.. slamat.. kaparehas pa ng car dto sa bahay un example mo hehe.. nid ko kc maintenance kc d masyado magamit car dto.. bka masira..

DCLXVI
24th Nov 2011, 15:35
I painted my APAD tablet :) nagkaproblema lang nung inakala ko na tuyo na, hindi pa pala :( pag matagal na nakadikit sa isang object, nagmarka siya hehe, sira ang paint job, paano kaya alisin ang pintura sa plastic? di naman kasi pwede lagyan paint remover hehe. nag print na lang ako ng sticker skin, at idinikit ko sa likod ng apad :)

john_aldz
24th Nov 2011, 16:09
Guys, baka me kilala naman kayong nagpapaint ng motor sa bandang olongapo or zambales. want to have my xrm re-painted, orange kasi kulay nia and di ko maxadong like kasi parang brown, eto po sample ng itsura nia but this is not mine. orange and color na nakaregister sa OR, ndi po ba magiging problema kung orange lang din ang kulay nia pagka re-paint? I just want a nicer look lang.

You can see links before reply

solo_baric
24th Nov 2011, 21:21
ah ok..ts.. slamat.. kaparehas pa ng car dto sa bahay un example mo hehe.. nid ko kc maintenance kc d masyado magamit car dto.. bka masira..

you're welcome bro.

:welcome:


I painted my APAD tablet :) nagkaproblema lang nung inakala ko na tuyo na, hindi pa pala :( pag matagal na nakadikit sa isang object, nagmarka siya hehe, sira ang paint job, paano kaya alisin ang pintura sa plastic? di naman kasi pwede lagyan paint remover hehe. nag print na lang ako ng sticker skin, at idinikit ko sa likod ng apad :)

anong klaseng pintura ba ginamit? subukan mong ipang tanggal ang acrylic thinner, try mo muna sa small portion ng Apad mo. i try mo kaya carbon fiber vinyl sa Apad mo, mas poporma yan. ididikit mo lang siya at madali lang ang proseso.

masisira kapag paint remover kasi plastic ang case.


Guys, baka me kilala naman kayong nagpapaint ng motor sa bandang olongapo or zambales. want to have my xrm re-painted, orange kasi kulay nia and di ko maxadong like kasi parang brown, eto po sample ng itsura nia but this is not mine. orange and color na nakaregister sa OR, ndi po ba magiging problema kung orange lang din ang kulay nia pagka re-paint? I just want a nicer look lang.

You can see links before reply

sorry bro. malayo area ko sa location mo. marami dyang pintor lalo sa olongapo.

dapat lang ibalik mo sa orange color ang xrm mo kasi yun ang nasa rehistro, kaya tama lang na ipa repaint mo siya ng orange.

juan2three
25th Nov 2011, 01:08
ayos ts... thanks.. napuyat ako kakabasa sa thread mo.. balak ko paint pick up namin.. post ko picture dito pag uwiko sa min.. sana tulungan moko.. thanks..

menggoy
25th Nov 2011, 01:50
sir ts paisang tanung pa po..bago lang kc kmi s sasakyan eh..pano po ba mag maintain ng sasakyan..hmmmm ano ba gawin na maintenance s 1 month 6 months 1 yir.....tuwing kelan pti pa tune up and anu ba mga oil na nilalagay at kelan.. bka kc mabulok un sasakyan dto.. dpa kc kmi nakakakuha ng non pro..tnx sa advance sir...

pa off topic lang thread starter,sagutin ko lang si sir...

ano ba oto mo? carb o efi?

tune is done every 6 months, depende kung pano mo gamitin kotse mo. kung daily driving. ok na every 6 months. usually pag sa tune up, basic na tsine check ay yung...

fuel filter, air filter, change oil ng engine (depende sa kotse mo kung anong gagamitin na oil, kung matanda na kotse mo, dapat mas malapot ang oil), brake fluid, power steering fluid (kung power steering tsikot mo), check mo sparkplugs kung ok pa(dapat nasa tamang clearance), valve clearance (ito yung bubuksan mo engine mo tapos i checheck ang clearance ng rocker arm, dapat na sa standard ang clearance nun. mahalaga ma maintain ang clearance, kasi pag hindi, wasak ang makina mo).

bago ka umalis ng bahay para gamitin ang kotse, icheck mo yung tubig ng radiator, mga oils (engine oil kung nasa tamang level ng dipstick. brake fluid,clutch fluid, power steering fluid, tire pressure.

sa kotse ko naman, ang maintenance ko every year (para malaki matipid ko, sa importanteng lakad lang kasi ginagamit). change oil, valve clearance, fuel filter. yung sparkplug at air filter, depende sa itsura kung kelangan ng palitan. pero every time na aalis ako,. tsine check ko yung namention ko sa taas.

nga pala, kung bihira mo gamitin ang kotse mo, kelangang pinapainit mo makina nito (paandarin mo makina ng mga 10 mins).once in 1 week pwede na. ginagawa ito para maiwasang tuluyang masira ang makina.

menggoy
25th Nov 2011, 02:10
I painted my APAD tablet :) nagkaproblema lang nung inakala ko na tuyo na, hindi pa pala :( pag matagal na nakadikit sa isang object, nagmarka siya hehe, sira ang paint job, paano kaya alisin ang pintura sa plastic? di naman kasi pwede lagyan paint remover hehe. nag print na lang ako ng sticker skin, at idinikit ko sa likod ng apad :)

sir, hindi talaga advisable ang pinturahan ang mga gadgets.di kasi pwedeng mabasa yan lalo na mga chemicals. tama si thread star ter, mga sticker dapat ginagamit dyan. mas mabilis ilapat, at mas mabilis tanggalin. kahit kelan na gusto mong palitan, kayang kaya. tama rin si thread starter na maporma yung carbon fiber na sticker.

K1Lm0r3
25th Nov 2011, 02:14
@TS baka gusto mo naman po mag-post ng step by step tutorial ng proper process ng pag-prepare at pag paint kahit sa acryllic based paints also achieving the showroom like stock finish. marami kang matutulungan dito :giggle:

john_aldz
25th Nov 2011, 05:18
sorry bro. malayo area ko sa location mo. marami dyang pintor lalo sa olongapo.

dapat lang ibalik mo sa orange color ang xrm mo kasi yun ang nasa rehistro, kaya tama lang na ipa repaint mo siya ng orange.


ayt ayt, Thanks po sa TIP

rukawa11
25th Nov 2011, 07:21
pa off topic lang thread starter,sagutin ko lang si sir...

ano ba oto mo? carb o efi?

tune is done every 6 months, depende kung pano mo gamitin kotse mo. kung daily driving. ok na every 6 months. usually pag sa tune up, basic na tsine check ay yung...

fuel filter, air filter, change oil ng engine (depende sa kotse mo kung anong gagamitin na oil, kung matanda na kotse mo, dapat mas malapot ang oil), brake fluid, power steering fluid (kung power steering tsikot mo), check mo sparkplugs kung ok pa(dapat nasa tamang clearance), valve clearance (ito yung bubuksan mo engine mo tapos i checheck ang clearance ng rocker arm, dapat na sa standard ang clearance nun. mahalaga ma maintain ang clearance, kasi pag hindi, wasak ang makina mo).

bago ka umalis ng bahay para gamitin ang kotse, icheck mo yung tubig ng radiator, mga oils (engine oil kung nasa tamang level ng dipstick. brake fluid,clutch fluid, power steering fluid, tire pressure.

sa kotse ko naman, ang maintenance ko every year (para malaki matipid ko, sa importanteng lakad lang kasi ginagamit). change oil, valve clearance, fuel filter. yung sparkplug at air filter, depende sa itsura kung kelangan ng palitan. pero every time na aalis ako,. tsine check ko yung namention ko sa taas.

nga pala, kung bihira mo gamitin ang kotse mo, kelangang pinapainit mo makina nito (paandarin mo makina ng mga 10 mins).once in 1 week pwede na. ginagawa ito para maiwasang tuluyang masira ang makina.

bro..laking tulong nito.. maraming salamat bro

solo_baric
25th Nov 2011, 12:23
ayos ts... thanks.. napuyat ako kakabasa sa thread mo.. balak ko paint pick up namin.. post ko picture dito pag uwiko sa min.. sana tulungan moko.. thanks..

sige lang sir 123. willing to help talaga sa mga ka symbian. kapag may budget kana, papinturahan mo na.


pa off topic lang thread starter,sagutin ko lang si sir...

ano ba oto mo? carb o efi?

tune is done every 6 months, depende kung pano mo gamitin kotse mo. kung daily driving. ok na every 6 months. usually pag sa tune up, basic na tsine check ay yung...

fuel filter, air filter, change oil ng engine (depende sa kotse mo kung anong gagamitin na oil, kung matanda na kotse mo, dapat mas malapot ang oil), brake fluid, power steering fluid (kung power steering tsikot mo), check mo sparkplugs kung ok pa(dapat nasa tamang clearance), valve clearance (ito yung bubuksan mo engine mo tapos i checheck ang clearance ng rocker arm, dapat na sa standard ang clearance nun. mahalaga ma maintain ang clearance, kasi pag hindi, wasak ang makina mo).

bago ka umalis ng bahay para gamitin ang kotse, icheck mo yung tubig ng radiator, mga oils (engine oil kung nasa tamang level ng dipstick. brake fluid,clutch fluid, power steering fluid, tire pressure.

sa kotse ko naman, ang maintenance ko every year (para malaki matipid ko, sa importanteng lakad lang kasi ginagamit). change oil, valve clearance, fuel filter. yung sparkplug at air filter, depende sa itsura kung kelangan ng palitan. pero every time na aalis ako,. tsine check ko yung namention ko sa taas.

nga pala, kung bihira mo gamitin ang kotse mo, kelangang pinapainit mo makina nito (paandarin mo makina ng mga 10 mins).once in 1 week pwede na. ginagawa ito para maiwasang tuluyang masira ang makina.

ayos pareng menggoy.. galing mo.


@TS baka gusto mo naman po mag-post ng step by step tutorial ng proper process ng pag-prepare at pag paint kahit sa acryllic based paints also achieving the showroom like stock finish. marami kang matutulungan dito :giggle:

plano ko talaga i post yang sinabi mo. sa ngayon collecting muna ako ng mga data at mga pictures para mas malinaw at detalyado ang tutorial. thanks for the support.


ayt ayt, Thanks po sa TIP

welcome sir.

:welcome:

randy m
26th Nov 2011, 11:17
sir pano kung repaint na ang motor ko may masilya na sya dati kaso bako bako masilya taz pylox lng ginamit na pintura, tatanggalin ko pa ba ang pintura pra masilyahan ng bago o kaya lihahin ko na lang ung bako bako at erepaint ulit ng pylox at pede bang lagyan clear coat yung pylox?

solo_baric
26th Nov 2011, 22:22
sir pano kung repaint na ang motor ko may masilya na sya dati kaso bako bako masilya taz pylox lng ginamit na pintura, tatanggalin ko pa ba ang pintura pra masilyahan ng bago o kaya lihahin ko na lang ung bako bako at erepaint ulit ng pylox at pede bang lagyan clear coat yung pylox?

huwag mo nang tanggalin ang masilya, lihain mo na lang ang masilya kung ok pa (gamitan mo ng kahoy na flat 3x5 inches ang size).

You can see links before reply

kung pumantay na apply ka ng putty para kuminis.

pagkatapos sprayan mo ng primer surfacer

You can see links before reply

patuyuin, lihain saka i paint ang kulay.

You can see links before reply 6Z8A


kahit pylox or any other brand basta acrylic paint pwede lagyan ng top coat clear na acrylic din.

PASENSYA NA MGA CAR PICTURES ANG MGA EXAMPLES KO.

rukawa11
27th Nov 2011, 16:09
ts lagi naman updated ung thread mo kaya dto nalang ulet me magtatanong.. ts alam mo ba kun magkano un silver na nakalagay sa windows ng car, dami ko kc nakikita na ganito, alam mo ba kun magkano or khit idea lang.. slamat

You can see links before reply

solo_baric
27th Nov 2011, 22:14
ts lagi naman updated ung thread mo kaya dto nalang ulet me magtatanong.. ts alam mo ba kun magkano un silver na nakalagay sa windows ng car, dami ko kc nakikita na ganito, alam mo ba kun magkano or khit idea lang.. slamat

You can see links before reply

mga 2-3 thousand siguro ang price nyan. manipis lang yan, nickel plated lang kaya maganda.

rukawa11
28th Nov 2011, 06:54
mga 2-3 thousand siguro ang price nyan. manipis lang yan, nickel plated lang kaya maganda.

slamat ts. 2-3 thousand ts.. magkabila na ba yun. nickel plated pala yan.. mrami ba klase nyan ts..?

solo_baric
28th Nov 2011, 21:14
slamat ts. 2-3 thousand ts.. magkabila na ba yun. nickel plated pala yan.. mrami ba klase nyan ts..?

oo, magkabila na yun. sa iba't ibang model, marami nyan. kung sa isang model ng car, isang klase lang yan.

deftechguy
29th Nov 2011, 06:18
sir, may itatanong lang po ako. thou it is not relevant sa car paintings, but sa furniture piano finish. may idea po ba kayo about this or may kakilala? may gamit kasi ako na nagasgasan, and piano finish ung top and bottom. pano po ba sir ito mairestore..pasensya na po sa OT sir.

rukawa11
29th Nov 2011, 08:01
oo, magkabila na yun. sa iba't ibang model, marami nyan. kung sa isang model ng car, isang klase lang yan.

tnx ulet ts.. ts magpapintura kmi ng kotse eh.. pahilamus na may konting gasgas. sa pinagtanungan namin 28k ang singil sobra mahal siguro quality un gamit nilang pintura pero sobra taas pa rin..dun sa kakilala nmin 15k daw pahilamus nya pero dko sure kun 15k sisingilin sa min..ksi sa liko ng kotse nmin may gasgas den dun sa harap crack un bumper kc nakaloward sya pero buo naman.den dun sa bubong meron bula bula na mukhang masilya rin.magkano kya sa tingin mu pre ang singil??

solo_baric
29th Nov 2011, 18:26
sir, may itatanong lang po ako. thou it is not relevant sa car paintings, but sa furniture piano finish. may idea po ba kayo about this or may kakilala? may gamit kasi ako na nagasgasan, and piano finish ung top and bottom. pano po ba sir ito mairestore..pasensya na po sa OT sir.

ano ba color ng piano? paint ba siya or varnish?


tnx ulet ts.. ts magpapintura kmi ng kotse eh.. pahilamus na may konting gasgas. sa pinagtanungan namin 28k ang singil sobra mahal siguro quality un gamit nilang pintura pero sobra taas pa rin..dun sa kakilala nmin 15k daw pahilamus nya pero dko sure kun 15k sisingilin sa min..ksi sa liko ng kotse nmin may gasgas den dun sa harap crack un bumper kc nakaloward sya pero buo naman.den dun sa bubong meron bula bula na mukhang masilya rin.magkano kya sa tingin mu pre ang singil??

masyadong mataas ang 28k. kahit pa mahal na pintura ang gamitin. lalot hilamos lang naman. yung 15k ang ideal price. kapag hilamos sa kotse, nagre range ito between 10-15k. pero be sure baka yung nag price ng 15k ay amateur car painter lang. dapat talaga canvas ng marami para mas maka mura pa.

rukawa11
29th Nov 2011, 18:59
masyadong mataas ang 28k. kahit pa mahal na pintura ang gamitin. lalot hilamos lang naman. yung 15k ang ideal price. kapag hilamos sa kotse, nagre range ito between 10-15k. pero be sure baka yung nag price ng 15k ay amateur car painter lang. dapat talaga canvas ng marami para mas maka mura pa. [/QUOTE]

uu nga pre..nabadtrip nga ako..kc pinagawa namin sa knila un banga sa side ng kotse halos kalahati nun left side ng kotse is 3k lang may kasama na syang pukpok at masilya..kya pag uwi nmin ng bhay naisipan na namin ipahilamus lahat un kotse,den nun tinawag namin s kanila,28k daw..anak ng patola. halos kalahati ng leftside ng car 3k,tpus un iba 25k.na anu kaya un sinisingil na yun.na iba..kaya yun d na namin pinaaus.yung banga nalang s gilid ang pinaaus namin ksi sagot ng ospital yun dhil sila naman nakabanga at sa doctor un carshop na pagawaan.. slmat ulet ts..

deftechguy
30th Nov 2011, 02:12
ano ba color ng piano? paint ba siya or varnish?

black pinano finish po za sir, parang lacquer ata ung ginagamit na pang pintura. glossy ung finishing nya.

menggoy
30th Nov 2011, 02:46
idol, ano ba tawag sa parang body filler rin na nasa lagayan na tulad ng toothpaste? ang gamit ba nun e ifi-fill nya yung mga maliliit na butas tsaka iis-smoothen nyan yung minasilyahan? saan po pweden makabili nun?

maraming salamat idol !

K1Lm0r3
30th Nov 2011, 03:30
idol, ano ba tawag sa parang body filler rin na nasa lagayan na tulad ng toothpaste? ang gamit ba nun e ifi-fill nya yung mga maliliit na butas tsaka iis-smoothen nyan yung minasilyahan? saan po pweden makabili nun?

maraming salamat idol !

paps baka yung hgardener ng masilya tinutukoy mo.


@ ts I have an upcoming project.. baka pwede mo ko tulungan TS.

I am planning to make a subwoofer enclosure.. gusto ko sana ,aiwasan maputukan ng masilya. (afterall pag pinagapang mo mahirap iwasan yun)

also yung prep na kelangan sa poper paint adhesion. planning to use self-etching primer kaso pang bakal ata :slap: and bosny paint for colors... baka guilder lang kunin ko pang top coat.

baka meron ka mas ok na suggestion :)

menggoy
30th Nov 2011, 03:34
paps baka yung hgardener ng masilya tinutukoy mo.




hindi sya hardener ng masilya, pero same sila ng lagayan tpos para atang mas malaki yung lagayan nung tinatanong ko.

solo_baric
1st Dec 2011, 05:35
idol, ano ba tawag sa parang body filler rin na nasa lagayan na tulad ng toothpaste? ang gamit ba nun e ifi-fill nya yung mga maliliit na butas tsaka iis-smoothen nyan yung minasilyahan? saan po pweden makabili nun?

maraming salamat idol !

siguro sealer/sealant ang ibig mong tukuyin o di kaya epoxy sealant?

You can see links before reply 7.jpg


paps baka yung hgardener ng masilya tinutukoy mo.


@ ts I have an upcoming project.. baka pwede mo ko tulungan TS.

I am planning to make a subwoofer enclosure.. gusto ko sana ,aiwasan maputukan ng masilya. (afterall pag pinagapang mo mahirap iwasan yun)

also yung prep na kelangan sa poper paint adhesion. planning to use self-etching primer kaso pang bakal ata :slap: and bosny paint for colors... baka guilder lang kunin ko pang top coat.

baka meron ka mas ok na suggestion :)

personal use mo ba? or business?

kahit gapang ang bass mo, hindi ka mapuputukan ng masilya kapag matibay ang wood na ginamit at adhesive.

gamit ka ng marine flywood, 3/4 ang kapal or 1 inch.

mga pwedeng gamiting adhesive:

marine epoxy non-sag - pinakamatibay sa mga nagamit ko

weldwood - matibay din, masisira na kahoy pero yung dikit hindi.

wood glue - least sa mga nabanggit pero matibay din sya.

pampatibay din bukod sa mga adhesive, i screw mga dugtungan o mga joints.

about paint brand, pwede na guilder kung sa enclosure lang naman.

gandoose
6th Dec 2011, 07:36
nice thread sir baric, marami ng natulungan ito

ken00
6th Dec 2011, 10:42
gud day po newbie rin ako sa motorcycles meron ditong motor na iniwan sa amin kasi sumakay ng barko yung owner guzto nya eh may mag alaga gusto ko sana irepaint.. kasi medyo haggard na tingnan gusto ko yellow at black na ang outcome eh yung glossy anu po tips nyo.. para dun and pede pa quote kung anu po gagamitin at panu gagawin kung kayang i DIY salamat po honda xrm po yung MC salamat TS

solo_baric
7th Dec 2011, 16:13
gud day po newbie rin ako sa motorcycles meron ditong motor na iniwan sa amin kasi sumakay ng barko yung owner guzto nya eh may mag alaga gusto ko sana irepaint.. kasi medyo haggard na tingnan gusto ko yellow at black na ang outcome eh yung glossy anu po tips nyo.. para dun and pede pa quote kung anu po gagamitin at panu gagawin kung kayang i DIY salamat po honda xrm po yung MC salamat TS

para maging glossy, kailangan ng top coat clear, branded para makintab. RM brand or any same level brand (malalaman sa price ng paint).

para maging glossy ang outcome, i paint ang top coat clear na walang halong color kundi top coat lang mixed with thinner.


PROCEDURES IN PAINTING CARS ARE MORE LIKELY IN PAINTING MOTORCYCLE.

rukawa11
11th Dec 2011, 15:25
ts..anu ba ang kaibahan ng 15k na hilamus pintura sa 25k na hilamus pintura.? totoo ba na mas makintab yung 25k na pintura kesa sa 15k, pati mas madali ba kumupas un low quality na 15k na hilamus?

robiN70
12th Dec 2011, 23:47
boss master, ask ko lang kung saan mai murang papinturahan ng kotse near sta.maria bulacan, un maganda maglagay ng design sa body, and maganda mag finish.. at ung hindi pakikielaman ung kotse mu hehe,, thanks

rgglenn150
13th Dec 2011, 00:11
may question lang po ako.. mejo off topic...pwede ba ung paint sa car gamitin sa electric guitar?

Gaslen88
13th Dec 2011, 16:41
bookmark,plan ko repaint motor ko eh.basa basa muna ako thank you TS sa thread na to.

menggoy
20th Dec 2011, 04:42
sirs, pa off topic lang po,may alam po ba kayong bilihan ng vinyl stickers na mura? gagawa po kasi ako ng tribal after mapinturahan ang kotse. balak ko po kasing bumili ng 1 roll.

markjames
20th Dec 2011, 08:58
ganda talaga ng thread na ito gustong gusto ko talaga matuto ng pag pain.. may compresor kami dito la naman may alam samin pano gamitin whehehe

solo_baric
20th Dec 2011, 09:05
ts..anu ba ang kaibahan ng 15k na hilamus pintura sa 25k na hilamus pintura.? totoo ba na mas makintab yung 25k na pintura kesa sa 15k, pati mas madali ba kumupas un low quality na 15k na hilamus?

kung the same shop o talyer yung nag price nyan, sa 25k, tiyak mahal na brand ng pintura ang gagamitin nila. syempre mas quality yun ay durable. madaling kumupas ang low quality na paint, pero depende rin sa alaga ng car. kahit quality pero kapag pinabayaan ay madali ring kukupas.


boss master, ask ko lang kung saan mai murang papinturahan ng kotse near sta.maria bulacan, un maganda maglagay ng design sa body, and maganda mag finish.. at ung hindi pakikielaman ung kotse mu hehe,, thanks

sorry tol, wala akong alam sa mga shop at location nila.

mag canvas ka na lang sa mga shop at magtanong tanong ka sa mga nakapagpa pintura na ng mga car nila. about body design, hindi yan karaniwan kaya mahihirapan kang maghanap.


bookmark,plan ko repaint motor ko eh.basa basa muna ako thank you TS sa thread na to.

welcome sir.

:welcome:


sirs, pa off topic lang po,may alam po ba kayong bilihan ng vinyl stickers na mura? gagawa po kasi ako ng tribal after mapinturahan ang kotse. balak ko po kasing bumili ng 1 roll.

sa mga car accessories ka makakabili nyan karaniwan sa mga car audio shop. canvas ka na lang para ma check mo kung saan mura.

rukawa11
21st Dec 2011, 16:59
TS un 15k ba na pintura at 25k na pintura ..same din ba sila ng quality sa physical appearance,nagkakaiba lang sa durability ????

solo_baric
22nd Dec 2011, 11:21
TS un 15k ba na pintura at 25k na pintura ..same din ba sila ng quality sa physical appearance,nagkakaiba lang sa durability ????

mag kaiba sila ng appearance maging sa durability.
para makatiyak ka about price, ask mo sila kung anong brand ng paint ang gagamitin nila sa 15k at 25k. then, ipost mo uli para malaman natin ang kaibahan nila.

dhars
22nd Dec 2011, 11:41
sir ako din ask about motor. gus2 ko sana ipachrome crankcase ng tmx 155 ko. Panu ba ung pagcochrome sir iniisprayhan lng o tinutubog?hehe!cnsya na wl tlg ako idea. Tska may pangspray na chrome dpo b?parang pylox.pwd rin ba un?

xDJx
22nd Dec 2011, 12:30
sir, yung mga rattlecan paints acrylic siya 'di ba?


pwede bang acrylic and base color tapos patungan ng polyurethane clear coat?

solo_baric
23rd Dec 2011, 10:10
sir ako din ask about motor. gus2 ko sana ipachrome crankcase ng tmx 155 ko. Panu ba ung pagcochrome sir iniisprayhan lng o tinutubog?hehe!cnsya na wl tlg ako idea. Tska may pangspray na chrome dpo b?parang pylox.pwd rin ba un?

sir, ang pagko CHROME ay tubog. may paint na chrome alike pero malayo siya sa itsura ng talagang chrome.


sir, yung mga rattlecan paints acrylic siya 'di ba?


pwede bang acrylic and base color tapos patungan ng polyurethane clear coat?

maraming klase ang can paint. may acrylic at laquer, meron ding enamel.

hindi pwedeng patungan ng urethane ang acrylic. kukulo siya. meaning lulusawin niya yung acrylic at masisira ang pintura.

pwede ang urethane patungan ng acrylic paint pero hindi na siya pwedeng patungan ng urethane ule.

dhars
23rd Dec 2011, 10:40
maraming salamat po sir.. 1more thing may idea po ba kayo master kung magkanu abutin ng pagpapa chrome ng buong makina ng MC ko?

dazed_confused
24th Dec 2011, 22:16
ts, gusto kong palitan ng kulay yung advie ko.gusto ko ring palagyan ng image sa hood using airbrush..mga magkano kaya estimate na magastos ko? salamat marami :)

xDJx
25th Dec 2011, 15:21
maraming klase ang can paint. may acrylic at laquer, meron ding enamel.

hindi pwedeng patungan ng urethane ang acrylic. kukulo siya. meaning lulusawin niya yung acrylic at masisira ang pintura.

pwede ang urethane patungan ng acrylic paint pero hindi na siya pwedeng patungan ng urethane ule.


maraming salamat :clap:

cyrus van
26th Dec 2011, 13:08
Tnx sa thread .. I have a lot of questions talaga.

Ano po ba ang paint na bagay sa moke belcher "TAMBUTSO" ng Motor?
Name the paint po at estimated price..

SAlAMAT:clap:

solo_baric
26th Dec 2011, 19:52
maraming salamat po sir.. 1more thing may idea po ba kayo master kung magkanu abutin ng pagpapa chrome ng buong makina ng MC ko?

welcome sir. sorry sir, wala akong idea about price ng chrome. never pa kasi ako nagpa chrome. canvas na lang kayo.



ts, gusto kong palitan ng kulay yung advie ko.gusto ko ring palagyan ng image sa hood using airbrush..mga magkano kaya estimate na magastos ko? salamat marami :)

pertaining to your likes about airbrush painting. customized painting na yan. usually talagang mahal ang magpapintura ng ganyan. halos doble ang price nyan sa karaniwang pagpaint ng sasakyan.

You can see links before reply


maraming salamat :clap:

welcome sir :welcome:


Tnx sa thread .. I have a lot of questions talaga.

Ano po ba ang paint na bagay sa moke belcher "TAMBUTSO" ng Motor?
Name the paint po at estimated price..

SAlAMAT:clap:

may heatproof na paint. VHT brand meron sila nito. medyo madalang kasi gumagamit nito satin. imbes na paint, chrome na ang pinipili ng iba.

dhars
28th Dec 2011, 19:55
VHT brand heat proof? Pwd rin yan sa makina master? Yan nalang kaya imbes pachrome? May kulay din kayang chrome ung VHT na yan?

perezmarvin
29th Dec 2011, 22:19
mga pare...anu bang magandang gamting spray paint in can, para s swing arm ng motorcycle q...ung matibay at kyang tumagal s init.,,,,

at ung madali lang din mabili....bosny lang alam q eh...hehehe....kya lang parang di aq satisfied sa knya and honestly la pa rin aqng lam bout car painting...

hope anyone ryply tnx po ng marmi

rukawa11
30th Dec 2011, 06:46
bro pag wla ba garahe dun lang sa kalsada na mainit naka tambay yun kotse pano ba maaalagaan yun kulay nun para d kumupas.. pwd na ba yung cover sa kotse para di ma direk sunlight or kaylangan tlga nakalilim.. may iba pa ba paraan para maalagaan ang kulay ng kotse without garahe..hehe

nhel1827
30th Dec 2011, 09:24
BOSS BKA MGLING K DIN SA DESIGN SA MGA MOTOR,,XRM 125 (BALCK RED ANG KULAY) want ko sana prepaint kso ala me idea sa design ng repiant bka mas lalo pumangit eh

perezmarvin
30th Dec 2011, 19:20
mga pare...anu bang magandang gamting spray paint in can, para s swing arm ng motorcycle q...ung matibay at kyang tumagal s init.,,,,

at ung madali lang din mabili....bosny lang alam q eh...hehehe....kya lang parang di aq satisfied sa knya and honestly la pa rin aqng lam bout car painting...

hope anyone ryply tnx po ng marmi



up q lng po

solo_baric
1st Jan 2012, 16:57
VHT brand heat proof? Pwd rin yan sa makina master? Yan nalang kaya imbes pachrome? May kulay din kayang chrome ung VHT na yan?

oo, pwedeng pwede yan. meron siguro pero di sya katulad na katulad ng chrome. try mo na lang mag canvas.


mga pare...anu bang magandang gamting spray paint in can, para s swing arm ng motorcycle q...ung matibay at kyang tumagal s init.,,,,

at ung madali lang din mabili....bosny lang alam q eh...hehehe....kya lang parang di aq satisfied sa knya and honestly la pa rin aqng lam bout car painting...

hope anyone ryply tnx po ng marmi

maraming brand ngayon na pwedeng mabili na in can. magbatay ka sa price. kapag mataas ang price meaning ay mas quality at durable ang paint. pero ingat din baka dun lang sa store na yun mataas. dapat ay canvas atleast 3 stores. kung gusto mo talagang heat proof, may nabibili nun. ask lang sa mga tindahan.


bro pag wla ba garahe dun lang sa kalsada na mainit naka tambay yun kotse pano ba maaalagaan yun kulay nun para d kumupas.. pwd na ba yung cover sa kotse para di ma direk sunlight or kaylangan tlga nakalilim.. may iba pa ba paraan para maalagaan ang kulay ng kotse without garahe..hehe

pwede na rin ung kulambo kung tawagin. pero maiinitan pa rin ang kotse dahil nakadikit sya sa car mismo, lalagos pa rin ang init. dapat talaga ay naka lilim ang sasakyan. tent na lang para sa car para less gastos kaysa magpagawa ng garahe.



BOSS BKA MGLING K DIN SA DESIGN SA MGA MOTOR,,XRM 125 (BALCK RED ANG KULAY) want ko sana prepaint kso ala me idea sa design ng repiant bka mas lalo pumangit eh


up q lng po

iilan pa lang napipinturahan kong motor. advise ko sayo tingin ka sa mga magazine ng mga motorcyle. doon ka makakakita ng mga customized paint ng mga motor.


:thumbsup::thumbsup:

BassBooster
1st Jan 2012, 23:08
SOLO-BARIC musta ka na.. happy new year..
nga pala may ask lang ako sayo about sa paint..
anong mixture po ba ang dapat gawin para maging..
fluorescent color ang kalabasan..
yung matingkad ang kulay sa gabi..
like this..
You can see links before reply mw

You can see links before reply

You can see links before reply

maganda kasi i-pintura sa mags ng motor eh