Default wifi password ng Globe Broadband B200W?

[riskbreaker15]

mga sir ano po default wifi password ng
Globe Broadband B200W..plagi kc ni rreset ung
modem d2 sa bahay(hard reset ung button sa likod)
kya palitan ko man ang password useless din..
sna po m2lungan nyo ako

[Jhowell75]

pag admin, gtadmin, pag user, user.

[riskbreaker15]

ndi po ung access password ang hinahanap ko..
ung default wifi password after ma reset ung modem

[denvah]

double post

[Link available to registered users only. Click here to register.]

[joethegreat]

Globe broadband B200W ba na may wifi o router ang tinutukoy mo?

[jefferson22493]

Aabbccddee

[KESTAY]

up ko lang meron din ako ganito,karereset ko.meron default pasword sa wifi.sino po ang may alam?tnx

[vannex19]

B200W default password
Default password for gateway: gtadmin (for admin), user (for user)
Default password for wifi: unknown ( it means I don’t know, but don’t lose hope I have a remedy for this)
Every time you hard reset the device the default profile will be “Globe” (base on my experience), during this mode you cannot connect to the internet neither by LAN nor by WIFI (if you are using a postpaid sim). In order connect to the internet you should select the correct profile depending on the sim you are using (ex. If you are using a prepaid sim you must select the “Prepaid” profile, and if you are using a postpaid sim you must select the “Postpaid” profile). But you cannot change the profile because there is no other option in the profile after your broadband had been reset. In order to do that you must make a profile that named either Postpaid or Prepaid, depending on the sim that you will use.
To do this connect your B200W Globe broadband to your computer, turn it ON, open the gateway, type 92.168.1.1/globe in any browser you want (Explorer, Mozilla or Google Chrome etc.)
Enter the password: gtadmin
go to Admin Settings - 3G Settings - Profile Settings and enter the following on the space provided:
if you are using a Postpaid sim.
Profile Name: Globe Postpaid
Dial-up Number: *99#
PPP User Name: (leave it blank)
PPP Password: (leave it blank)
APN:
( ) Dynamic ( x ) Static internet.globe.com.ph Note: select Static
IP Address:
( x ) Dynamic ( ) Static (leave it blank) Note: select Dynamic

Then select save.

if you are using a Prepaid sim.
Profile Name: Globe Postpaid
Dial-up Number: *99#
PPP User Name: (leave it blank)
PPP Password: (leave it blank)
APN:
( ) Dynamic ( x ) Static http.globe.com.ph Note: select Static
IP Address:
( x ) Dynamic ( ) Static (leave it blank) Note: select Dynamic

Then select save.
To select the Profile option you made go to Admin Settings - 3G Settings - PPP Settings

Profile List: Select either Globe Postpaid or Globe Prepaid

Just leave the options below as is, then click apply.

Please see the video tutorial [Link available to registered users only. Click here to register.] (credits to akomismo01 )


To connect your computer to your broadband via wifi go to Advance Settings - Wi-Fi Settings - Wi-Fi Advance Settings
And select the following:
Wireless Interface: (leave as is)
802.11 Authentication: select open
Encryption Mode: NO ENCRYPTION

Then click apply, and you are DONE!.......
But this will leave tour Wi-fi open to anyone and they could connect to your internet freely.

If you want to put a wi-fi password go to Advance Settings - Wi-Fi Settings - Wi-Fi Advance Settings
And select the following:

Wireless Interface: (leave as is)
802.11 Authentication: select open
Encryption Mode: WPA – PSK or WPA2 – PSK
WPA Encryption: TKIP
WPA Pre-Shared Key: (type the password you want)
Key Rotation Interval: 0

Then click apply, and you are DONE!.......
sana po naka tulong...

To Moderators: paki delete nyo nalang po kung sa tingin nyo po ay repost na ito.

[Chainsmoker]

B200W default password
Default password for gateway: gtadmin (for admin), user (for user)
Default password for wifi: unknown ( it means I don’t know, but don’t lose hope I have a remedy for this)
Every time you hard reset the device the default profile will be “Globe” (base on my experience), during this mode you cannot connect to the internet neither by LAN nor by WIFI (if you are using a postpaid sim). In order connect to the internet you should select the correct profile depending on the sim you are using (ex. If you are using a prepaid sim you must select the “Prepaid” profile, and if you are using a postpaid sim you must select the “Postpaid” profile). But you cannot change the profile because there is no other option in the profile after your broadband had been reset. In order to do that you must make a profile that named either Postpaid or Prepaid, depending on the sim that you will use.
To do this connect your B200W Globe broadband to your computer, turn it ON, open the gateway, type 92.168.1.1/globe in any browser you want (Explorer, Mozilla or Google Chrome etc.)
Enter the password: gtadmin
go to Admin Settings - 3G Settings - Profile Settings and enter the following on the space provided:
if you are using a Postpaid sim.
Profile Name: Globe Postpaid
Dial-up Number: *99#
PPP User Name: (leave it blank)
PPP Password: (leave it blank)
APN:
( ) Dynamic ( x ) Static internet.globe.com.ph Note: select Static
IP Address:
( x ) Dynamic ( ) Static (leave it blank) Note: select Dynamic

Then select save.

if you are using a Prepaid sim.
Profile Name: Globe Postpaid
Dial-up Number: *99#
PPP User Name: (leave it blank)
PPP Password: (leave it blank)
APN:
( ) Dynamic ( x ) Static http.globe.com.ph Note: select Static
IP Address:
( x ) Dynamic ( ) Static (leave it blank) Note: select Dynamic

Then select save.
To select the Profile option you made go to Admin Settings - 3G Settings - PPP Settings

Profile List: Select either Globe Postpaid or Globe Prepaid

Just leave the options below as is, then click apply.

Please see the video tutorial [Link available to registered users only. Click here to register.] (credits to akomismo01 )


To connect your computer to your broadband via wifi go to Advance Settings - Wi-Fi Settings - Wi-Fi Advance Settings
And select the following:
Wireless Interface: (leave as is)
802.11 Authentication: select open
Encryption Mode: NO ENCRYPTION

Then click apply, and you are DONE!.......
But this will leave tour Wi-fi open to anyone and they could connect to your internet freely.

If you want to put a wi-fi password go to Advance Settings - Wi-Fi Settings - Wi-Fi Advance Settings
And select the following:

Wireless Interface: (leave as is)
802.11 Authentication: select open
Encryption Mode: WPA – PSK or WPA2 – PSK
WPA Encryption: TKIP
WPA Pre-Shared Key: (type the password you want)
Key Rotation Interval: 0

Then click apply, and you are DONE!.......
sana po naka tulong...

To Moderators: paki delete nyo nalang po kung sa tingin nyo po ay repost na ito.

Galing naman, salamat po sa tuts nyo, up natin sa mga nangagailangan.