Welcome back, Guest!
Register
Forgot your Password?

Hello, Guest! Welcome to Symbianize Forum.

Most of our features and services are available only to our members. So we encourage you to login or join us by registering a new account. Registration is free, fast, and simple. You only need to provide a valid email address so we can minimize spammers. As a Symbianize member you'll have the following privileges:

All that and more, so what are you waiting for, join us now! Ito ang website na ginawa ng pinoy para sa pinoy!

Page 1 of 2 12 LastLast
Results 1 to 10 of 19
  1. #1

    Default NOKIA X2-01 security code/keypad locked reset

    FACTORY RESET security code 12345 using PHOENIX TEST & SERVICE SOFTWARE and USB cable

    i forgot my NOKIA X2-01 security code.
    i can't use my phone.
    my PC can't detect USB because SECURITY CODE is locked.
    keypad is locked.


    FACTORY RESET NOKIA X2-01 (reset security code to 12345)
    using PHOENIX TEST & SERVICE SOFTWARE

    1. how to make USB nokia X2-01 to be detected by your PC.

    = connect a RESISTOR (about 5K ohms) between the BATTERY TERMINALS = BS1 (center) and GND (-).

    [Link available to registered users only. Click here to register.]
    in my case, i don't have 5kOhms. i used resistors in series but only about 3.8kOhms total)
    [Link available to registered users only. Click here to register.]
    i used old cd-rom audio cable and used the terminal to connect to the battery terminals BS1(center) and GND (-).
    i soldered the series resistors to the other end of the audio cable.
    [Link available to registered users only. Click here to register.]


    2. PHOENIX Test & Service Software INSTALLATION
    = before installing PHOENIX
    remove all NOKIA related softwares, PC SUITE, SOFTWARE UPDATER, CONNECTIVITY CABLE
    =disable all anti-virus
    =PROCEED to PHOENIX SETUP (takes time)

    3. insert micro USB cable to your NOKIA X2-01 and connect to PC
    = wait for all USB Drivers to be detected
    = click phoenix

    [Link available to registered users only. Click here to register.]
    = SCAN PRODUCT
    [Link available to registered users only. Click here to register.]
    = RM-709
    [Link available to registered users only. Click here to register.]
    = TESTING
    = FACTORY SETTINGS
    [Link available to registered users only. Click here to register.]
    =FACTORY SET FULL
    =WRITE
    [Link available to registered users only. Click here to register.]
    = switch to test mode ? NO
    [Link available to registered users only. Click here to register.]
    = write to phone ? YES
    [Link available to registered users only. Click here to register.]
    = SUCCESSFUL
    [Link available to registered users only. Click here to register.]
    =PHOENIX VERSION
    [Link available to registered users only. Click here to register.]
    = disconnect USB from PC.
    = remove resistor
    = switch on your NOKIA X2-01
    = enter SECURITY CODE === 12345

    YOU CAN DO IT.
    Last edited by jerik2005; 29th Apr 2011 at 10:43.

  2. #2

    Default Re: NOKIA X2-01 security code/keypad locked reset

    Hindi b pwdeng instolan nlng ng bagong firmware at reflash nlng? Bagong option? nice thread..

  3. #3

    Default Re: NOKIA X2-01 security code/keypad locked reset

    pwedeng pwede.
    kaya lang matagal kung mag-re- flash ka.

    i only need to reset the security code back to 12345.
    it takes only a couple of seconds by phoenix to do a factory reset.

    another thing:
    wala rin akong nahanap na firmware for my
    X2-01 product code ==> t_059C3L5
    i doubt baka may incompatibilities pag i-reflash ko ng iba sa code.

    share ko lang, sana makatulong.

  4. #4

    Default Re: NOKIA X2-01 security code/keypad locked reset

    ang problema kasi nito hindi talaga madetect ng PC ang USB
    kapag naka KEYPAD LOCK at saka ON yong' SECURITY CODE,


    ::>last tuesday, i went to a cellphone repair shop inside SM City Cebu. pinabalik ako after 2 hours, akala ko na factory reset na yong phone ko, hindi pala nila nagawa. sabi nila, ayaw daw ma detect ng PC ang USB, so, ibinalik sa akin ang phone tapos hingi sila ng 50 pesos charge. sabi ko, bakit pa ako magbabayad, ni wala naman kayong nagawa. i insisted, i-cancel nalang yong transaction slip, isuli sa akin ang phone, at wala akong babayaran. buti nalang mabait yong kausap ko. pumayag naman.

    ::>bumili nalang ako ng micro usb cable sa CDR-KING for 50 PESOS. hehehe.

    ::>D.I.Y. na lang ako. LIBRE PA.
    Last edited by jerik2005; 16th May 2011 at 09:32.

  5. #5

    Default Re: NOKIA X2-01 security code/keypad locked reset

    PC can't detect NOKIA USB kasi naka keypad lock at nakalimotan ang security code.

  6. #6

    Default Re: NOKIA X2-01 security code/keypad locked reset

    meron na pong bagong firmware di ko lang alam kung anong nabago hihihih

  7. #7

    Default Re: NOKIA X2-01 security code/keypad locked reset

    sir jerik2005 confirmed na working po sa ibang s40v5/s40v6 models ang inyong solution.
    malaking ambag po ito sa ikauunlad ng mga phone naten

    ganito naman po ginawa ko:

    materials:
    4K7 ohm resistor
    old cd-rom cable

    kumuha po ako ng isang 4K7 resistor sa lumang nokia charger

    wala po akong panghinang
    kaya naghanap na rin ako ng cd-rom cable na may plug sa magkabilang dulo. doon ko ngayon sinuksok ang 4K7 resistor sa plastic plug

    inalis ko yung isa pang dulo ng cable para ma i-link sa batt terminal na sinabi ninyo
    BATTERY TERMINAL (BS1)&(-)

    para po naman mas maliit ang mga piyesang ginamit sa homebrewed cable.

    tapos po sundin na lang yung mga instructions ninyo sa itaas.

    isa po itong malaking tulong sir!

    maraming salamat po!

  8. #8

    Default Re: NOKIA X2-01 security code/keypad locked reset

    maoopenline ba pag niflash?

  9. #9

    Default Re: NOKIA X2-01 security code/keypad locked reset

    Bookmarked.

  10. #10

    Default Re: NOKIA X2-01 security code/keypad locked reset

    mga sir meron po ako cp na may security code di rin ma detect ng pc di ko po masyado naintindihan ung tuts, san po ba ikakabit ung resistor? bali 2 wire lng po ba ito ung dulo sa battery terminal then ung resistor sa kabilang dulo nman ganun po ba?

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •