B315s-936 No Light After Reflashing (New Firmware = 21.313.06.02.158)

[jeface2012]

After kung ireflash using BALONG method

1. Open Balong USB Downloader
- Click Detect
- Locate usblsafe-b315.bin
- Load
- Pag 100% na close.

2. Open Firmware Folder
- Click go_hdlc
- Enter

3. Open Huawei R215 Flash
- Locate 3G PC UI Interface (select)
- Flash
- Locate .hmf file
- Antayin na may nakasulat na Done/Remove battery and put it again..
- Close

4. Unplug Power, Unplug USB, unplug Flasher

5. Plug Power Chord, Plug LAN cable
(After this point No lights talaga then nanotice ko na pag-iplug ko yung usb detected siya sa pc and power light lang ang may ilaw)
View attachment 295340

 

[inutell]

detected ba com port?
try mo flash sa lan.

 

[sb0x24]

After kung ireflash using BALONG method

1. Open Balong USB Downloader
- Click Detect
- Locate usblsafe-b315.bin
- Load
- Pag 100% na close.

2. Open Firmware Folder
- Click go_hdlc
- Enter

3. Open Huawei R215 Flash
- Locate 3G PC UI Interface (select)
- Flash
- Locate .hmf file
- Antayin na may nakasulat na Done/Remove battery and put it again..
- Close

4. Unplug Power, Unplug USB, unplug Flasher

5. Plug Power Chord, Plug LAN cable
(After this point No lights talaga then nanotice ko na pag-iplug ko yung usb detected siya sa pc and power light lang ang may ilaw)
View attachment 1168634

eh baka nman kac di m0 tinanggaL ung nka t0p m0ng wire, wag mgmamadaLi sa pg 0penLine at pg debrand ng new 936, pakaLmahin m0 utak m0 0t0r, kaw Lng mag err0r na gnyan, ka eng0tan yan

 

[jeface2012]

detected ba com port?
try mo flash sa lan.

Yes Sir detected yung com port kaso yung lan not detected sir. Walang ilaw lahat sir pero pagplug ko yung usb detected naman... Anong gawin ko sir...

 

[knip]

sir? Hindi naman po kaingutan ang pagkakamali.
kung magaling kana. Sana tinulungan mo nalang si otor keysa ganyanin mo pa.

 

[at0m]

After kung ireflash using BALONG method

1. Open Balong USB Downloader
- Click Detect
- Locate usblsafe-b315.bin
- Load
- Pag 100% na close.

2. Open Firmware Folder
- Click go_hdlc
- Enter

3. Open Huawei R215 Flash
- Locate 3G PC UI Interface (select)
- Flash
- Locate .hmf file
- Antayin na may nakasulat na Done/Remove battery and put it again..
- Close

4. Unplug Power, Unplug USB, unplug Flasher

5. Plug Power Chord, Plug LAN cable
(After this point No lights talaga then nanotice ko na pag-iplug ko yung usb detected siya sa pc and power light lang ang may ilaw)
View attachment 1168634

just repeat it again procedure 1,2 and 3,dont go to no 4 yet,wait first all the lights to goes out except the power led...then proceed to no 4 procedure

 

[khraine14]

hanap ka ng good files ng 11 bin... my kalat dito na sablay... ilang ulit ko ginamit yun laging stuck sa power on... nung nag try ako ibang bin files un after reboot sa flasher good boot up...

 

[Chakman]

hanap ka ng good files ng 11 bin... my kalat dito na sablay... ilang ulit ko ginamit yun laging stuck sa power on... nung nag try ako ibang bin files un after reboot sa flasher good boot up...

san mo nahanap ts? hirap kasi maghanap eh.

 

[cryx25]

Na solve mo ba to ts?

 

[macchu]

akin nga sir lahat walang ilaw eh kc ginawa ko shortcut flashing aun no led lahat pero nagawa ng led repair files ni sir jansen