NOKIA X2-01 security code/keypad locked reset

[jerik2005]

FACTORY RESET security code 12345 using PHOENIX TEST & SERVICE SOFTWARE and USB cable

i forgot my NOKIA X2-01 security code.
i can't use my phone.
my PC can't detect USB because SECURITY CODE is locked.
keypad is locked.


FACTORY RESET NOKIA X2-01 (reset security code to 12345)
using PHOENIX TEST & SERVICE SOFTWARE

1. how to make USB nokia X2-01 to be detected by your PC.

= connect a RESISTOR (about 5K ohms) between the BATTERY TERMINALS = BS1 (center) and GND (-).

in my case, i don't have 5kOhms. i used resistors in series but only about 3.8kOhms total)

i used old cd-rom audio cable and used the terminal to connect to the battery terminals BS1(center) and GND (-).
i soldered the series resistors to the other end of the audio cable.

2. PHOENIX Test & Service Software INSTALLATION
= before installing PHOENIX
remove all NOKIA related softwares, PC SUITE, SOFTWARE UPDATER, CONNECTIVITY CABLE
=disable all anti-virus
=PROCEED to PHOENIX SETUP (takes time)

3. insert micro USB cable to your NOKIA X2-01 and connect to PC
= wait for all USB Drivers to be detected
= click phoenix

= SCAN PRODUCT

= RM-709

= TESTING
= FACTORY SETTINGS

=FACTORY SET FULL
=WRITE

= switch to test mode ? NO

= write to phone ? YES

= SUCCESSFUL

=PHOENIX VERSION

= disconnect USB from PC.
= remove resistor
= switch on your NOKIA X2-01
= enter SECURITY CODE === 12345

YOU CAN DO IT.

 

[Sanji_19]

Hindi b pwdeng instolan nlng ng bagong firmware at reflash nlng? Bagong option? nice thread..

 

[jerik2005]

pwedeng pwede.
kaya lang matagal kung mag-re- flash ka.

i only need to reset the security code back to 12345.
it takes only a couple of seconds by phoenix to do a factory reset.

another thing:
wala rin akong nahanap na firmware for my
X2-01 product code ==> t_059C3L5
i doubt baka may incompatibilities pag i-reflash ko ng iba sa code.

share ko lang, sana makatulong.

 

[jerik2005]

ang problema kasi nito hindi talaga madetect ng PC ang USB
kapag naka KEYPAD LOCK at saka ON yong' SECURITY CODE,


::>last tuesday, i went to a cellphone repair shop inside SM City Cebu. pinabalik ako after 2 hours, akala ko na factory reset na yong phone ko, hindi pala nila nagawa. sabi nila, ayaw daw ma detect ng PC ang USB, so, ibinalik sa akin ang phone tapos hingi sila ng 50 pesos charge. sabi ko, bakit pa ako magbabayad, ni wala naman kayong nagawa. i insisted, i-cancel nalang yong transaction slip, isuli sa akin ang phone, at wala akong babayaran. buti nalang mabait yong kausap ko. pumayag naman.

::>bumili nalang ako ng micro usb cable sa CDR-KING for 50 PESOS. hehehe.

::>D.I.Y. na lang ako. LIBRE PA.

 

[jerik2005]

PC can't detect NOKIA USB kasi naka keypad lock at nakalimotan ang security code.

 

[brdevilzyan]

meron na pong bagong firmware di ko lang alam kung anong nabago hihihih

 

[rockmann_exe]

sir jerik2005 confirmed na working po sa ibang s40v5/s40v6 models ang inyong solution.
malaking ambag po ito sa ikauunlad ng mga phone naten

ganito naman po ginawa ko:

materials:
4K7 ohm resistor
old cd-rom cable

kumuha po ako ng isang 4K7 resistor sa lumang nokia charger

wala po akong panghinang
kaya naghanap na rin ako ng cd-rom cable na may plug sa magkabilang dulo. doon ko ngayon sinuksok ang 4K7 resistor sa plastic plug

inalis ko yung isa pang dulo ng cable para ma i-link sa batt terminal na sinabi ninyo
BATTERY TERMINAL (BS1)&(-)

para po naman mas maliit ang mga piyesang ginamit sa homebrewed cable.

tapos po sundin na lang yung mga instructions ninyo sa itaas.

isa po itong malaking tulong sir!

maraming salamat po!

 

[VMren]

maoopenline ba pag niflash?

 

[jlmrbhunny]

Bookmarked.

 

[dastan69]

mga sir meron po ako cp na may security code di rin ma detect ng pc di ko po masyado naintindihan ung tuts, san po ba ikakabit ung resistor? bali 2 wire lng po ba ito ung dulo sa battery terminal then ung resistor sa kabilang dulo nman ganun po ba?

 

[anica27]

wala p0 bang hard press key nalang for x2 01?

 

[arkidzz]

is it ok on X3?

 

[loreliekilapkilap]

pwede po bang installan ng ibang application ang X2-01 natin?? like games ,, themes, blog and other connections.. etc.. please reply a link kung pwede or kung meron po..thnks...

 

[joptionpane]

pa marka dito bossing gawa muna ako 4k7 resistor

 

[eileenmetran]

Thank you so much po! back to default na security code ko ) keep it up!

 

[Ekkzhotikk]

sir, nainstall ko po yung software, ang problema hindi nadedetect nung phoenix yung X2-01 ko pero binabasa naman ng pc ko. nakakapagtransfer ako ng music sa cp ko e. hindi ko rin maclick yung scan sa phoenix. tiningnan ko yung list ng cp, wala dun yung x2-01 paano po kaya?

 

[eepyaj25]

pa bm sir salamat dito ,,

 

[jmabasa06]

Sir pwede dn nss pro para ma factory reset diba ? un kc ginamit ko .. hindi din mabasa ng phoenix the tinry ko ung nss nabasa nya ..

btw .. tnx sa tut sir

 

[jerik2005]

'm ckab <----

salamat sa lahat ng natutulungan sa thread na ito.

you can do it ...

 

[aesope]

FACTORY RESET security code 12345 using PHOENIX TEST & SERVICE SOFTWARE and USB cable

i forgot my NOKIA X2-01 security code.
i can't use my phone.
my PC can't detect USB because SECURITY CODE is locked.
keypad is locked.


FACTORY RESET NOKIA X2-01 (reset security code to 12345)
using PHOENIX TEST & SERVICE SOFTWARE

1. how to make USB nokia X2-01 to be detected by your PC.

= connect a RESISTOR (about 5K ohms) between the BATTERY TERMINALS = BS1 (center) and GND (-).

http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478264.jpg
in my case, i don't have 5kOhms. i used resistors in series but only about 3.8kOhms total)
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478257.jpg
i used old cd-rom audio cable and used the terminal to connect to the battery terminals BS1(center) and GND (-).
i soldered the series resistors to the other end of the audio cable.
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478248.jpg


2. PHOENIX Test & Service Software INSTALLATION
= before installing PHOENIX
remove all NOKIA related softwares, PC SUITE, SOFTWARE UPDATER, CONNECTIVITY CABLE
=disable all anti-virus
=PROCEED to PHOENIX SETUP (takes time)

3. insert micro USB cable to your NOKIA X2-01 and connect to PC
= wait for all USB Drivers to be detected
= click phoenix

http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478266.jpg
= SCAN PRODUCT
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478268.jpg
= RM-709
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478236.jpg
= TESTING
= FACTORY SETTINGS
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478238.jpg
=FACTORY SET FULL
=WRITE
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478237.jpg
= switch to test mode ? NO
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478265.jpg
= write to phone ? YES
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478239.jpg
= SUCCESSFUL
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478267.jpg
=PHOENIX VERSION
http://pic100.picturetrail.com/VOL1164/13357859/23784610/396478240.jpg
= disconnect USB from PC.
= remove resistor
= switch on your NOKIA X2-01
= enter SECURITY CODE === 12345

YOU CAN DO IT.

good day po sir. .i have the same problem po sa inyo. .NOKIA X2-01 po yung phone ko. .sinunod ko po yung tuts nyu. .na detect na po ang phone ko pero pag open ko ng phoenix. .hindi po ma click yung scan product. .ano po ba dapat gawin??please help po. .salamat