- Messages
- 101
- Reaction score
- 4
- Points
- 28
sa wakas BUTAS kana din...
U-Boot 2010.03-svn671412 (May 27 2017 - 09:37:39)
DRAM: 128 MB
Boot From NAND Flash
CHIP ID = 51152100
NAND: Special Nand id table Version 1.23
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4Bytes
128 MiB
env0 ok ~~~~~~~~~~~
In: serial
Out: serial
Err: serial
hi_lsw_init
hi_lsw_init_t
MEM_MODE = MEM!
tmp_cmd a =kk=112 mem=240M console=ttyAMA1,115200 root=/dev/mtdblock5 rootfstype=jffs2 mtdparts=hinand:128k(startcode),1M(u-bootA),1M(u-bootB),1M(envA),1M(envB),18M(kernel_rootfsA),18M(app_binA),20M(app_exA),18M(kernel_rootfsB),18M(app_binB),20M(app_exB),12160k(cfg)
kernel_rootfs_mtd_offset = 0x420000
Hit <enter> to stop autoboot: 2 1 0
(Re)start USB...
USB: hsan ehci start sucessful!
Register 1212 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... The request port(1) is not configured
## Booting kernel from Legacy Image at 82800000 ...
Image Name: Linux-2.6.34.10
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2208012 Bytes = 2.1 MB
Load Address: 80e08000
Entry Point: 80e08000
Verifying Checksum ... OK
Memory Start: 80e00000
hsan echi stop sucessful!
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Spi id table Version 1.22
Special nand id table Version 1.33
Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:4Bytes
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown MX30LF1G18AC)
NAND_ECC_NONE selected by board driver. This is not recommended !!
12 cmdlinepart partitions found on MTD device hinand
Creating 12 MTD partitions on "hinand":
0x000000000000-0x000000020000 : "startcode"
0x000000020000-0x000000120000 : "u-bootA"
0x000000120000-0x000000220000 : "u-bootB"
0x000000220000-0x000000320000 : "envA"
0x000000320000-0x000000420000 : "envB"
0x000000420000-0x000001620000 : "kernel_rootfsA"
0x000001620000-0x000002820000 : "app_binA"
0x000002820000-0x000003c20000 : "app_exA"
0x000003c20000-0x000004e20000 : "kernel_rootfsB"
0x000004e20000-0x000006020000 : "app_binB"
0x000006020000-0x000007420000 : "app_exB"
0x000007420000-0x000008000000 : "cfg"
mount file system
mount -t jffs2 /dev/mtdblock11 /fhcfg successfully!
get env:app_bin_flag,value:0 successfully!
mount -t jffs2 /dev/mtdblock6 /fh/bin successfully!
set app_bin_curr_flag to 0 successfully!
get env:app_ex_flag,value:0 successfully!
Empty flash at 0x00f5df08 ends at 0x00f5e000
mount -t jffs2 /dev/mtdblock7 /fh/extend successfully!
set app_ex_curr_flag to 0 successfully!
update :
ang galing ng pldtfibr tinanggal ba naman...
192.168.1.1/internet/wan_sfu.asp
View attachment 348823
U-Boot 2010.03-svn671412 (May 27 2017 - 09:37:39)
DRAM: 128 MB
Boot From NAND Flash
CHIP ID = 51152100
NAND: Special Nand id table Version 1.23
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4Bytes
128 MiB
env0 ok ~~~~~~~~~~~
In: serial
Out: serial
Err: serial
hi_lsw_init
hi_lsw_init_t
MEM_MODE = MEM!
tmp_cmd a =kk=112 mem=240M console=ttyAMA1,115200 root=/dev/mtdblock5 rootfstype=jffs2 mtdparts=hinand:128k(startcode),1M(u-bootA),1M(u-bootB),1M(envA),1M(envB),18M(kernel_rootfsA),18M(app_binA),20M(app_exA),18M(kernel_rootfsB),18M(app_binB),20M(app_exB),12160k(cfg)
kernel_rootfs_mtd_offset = 0x420000
Hit <enter> to stop autoboot: 2 1 0
(Re)start USB...
USB: hsan ehci start sucessful!
Register 1212 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... The request port(1) is not configured
## Booting kernel from Legacy Image at 82800000 ...
Image Name: Linux-2.6.34.10
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2208012 Bytes = 2.1 MB
Load Address: 80e08000
Entry Point: 80e08000
Verifying Checksum ... OK
Memory Start: 80e00000
hsan echi stop sucessful!
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Spi id table Version 1.22
Special nand id table Version 1.33
Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:4Bytes
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown MX30LF1G18AC)
NAND_ECC_NONE selected by board driver. This is not recommended !!
12 cmdlinepart partitions found on MTD device hinand
Creating 12 MTD partitions on "hinand":
0x000000000000-0x000000020000 : "startcode"
0x000000020000-0x000000120000 : "u-bootA"
0x000000120000-0x000000220000 : "u-bootB"
0x000000220000-0x000000320000 : "envA"
0x000000320000-0x000000420000 : "envB"
0x000000420000-0x000001620000 : "kernel_rootfsA"
0x000001620000-0x000002820000 : "app_binA"
0x000002820000-0x000003c20000 : "app_exA"
0x000003c20000-0x000004e20000 : "kernel_rootfsB"
0x000004e20000-0x000006020000 : "app_binB"
0x000006020000-0x000007420000 : "app_exB"
0x000007420000-0x000008000000 : "cfg"
mount file system
mount -t jffs2 /dev/mtdblock11 /fhcfg successfully!
get env:app_bin_flag,value:0 successfully!
mount -t jffs2 /dev/mtdblock6 /fh/bin successfully!
set app_bin_curr_flag to 0 successfully!
get env:app_ex_flag,value:0 successfully!
Empty flash at 0x00f5df08 ends at 0x00f5e000
mount -t jffs2 /dev/mtdblock7 /fh/extend successfully!
set app_ex_curr_flag to 0 successfully!
update :
ang galing ng pldtfibr tinanggal ba naman...
192.168.1.1/internet/wan_sfu.asp
View attachment 348823
Attachments
Last edited: