How to Openline (Unlock) and Debrand Huawei e5573cs-933 (Globe)

[khenkhen19]

Ok na pala. I used different cable at gumana na siya Salamat ts View attachment 333524

 

[Tommy 40588]

Salamat dito TS, makakatipid ako nito sa mga repair shops itatry ko to pag nakahanap na ako ng screwdriver na maliit pati conductor.

Tanong ko lang po pala, pati sa mga nakatry na, kailangan po ba to ng internet connection during the updating ng mga UI and unlocking process? Iisa lang kasi yung source ng internet namin dito sa bahay, ito lang mismong pocket wifi na iuunlock ko, kaya wala akong magagamit na net kapag gagawin ko na. po sa sasagot.

 

[jlvillanueva06]

Boss successfully unlocked na sakin. Ang di ko magets ayaw nya kumonek sa portal. Di ko rin maconnect through wifi (tried the default password not working) at usb cable di naman madetect. Paano to? Nakikita naman siya sa available wifi to connect

boss try mo pass 12345678

 

[richarddeo_fondevilla]

Salamat ng marami rito. Mamaya titirahin ko yung dalawang units ko. Hahaha

 

[egoless]

Sa mga naka openline, ano gamit niyong os? Ayaw kasi ma install nung FcSerialDrv sa windows 8. Nagpost na ako sa magkabilang forums wala pa din sumasagot.

 

[makipogz]

Sa mga naka openline, ano gamit niyong os? Ayaw kasi ma install nung FcSerialDrv sa windows 8. Nagpost na ako sa magkabilang forums wala pa din sumasagot.

windows 7/8 working to. windows 10 64 bit failed to initialize

 

[Tommy 40588]

Guys, tanong lang po sa pagbaklas nito. Yung nasa picture, yung mga may ekis natanggal ko na yung screw gamit nung T5 Torx.

View attachment 333795

Natanggal ko na yung lima, pero may napansin akong isang screw sa tabi ng simcard slot(yung may bilog sa picture) na natakpan ng white seal na parang papel, tinanggal ko yung seal tapos sinubukan kong tanggalin pero sobrang higpit niya, halos masira na ang ulo ng screw.

Tanong ko lang kung kasama pa ba siyang tanggalin yung may bilog sa picture para mabaklas ko yung likod o kahit hindi na? Salamat sa sasagot

 

[makipogz]

Guys, tanong lang po sa pagbaklas nito. Yung nasa picture, yung mga may ekis natanggal ko na yung screw gamit nung T5 Torx.

View attachment 1238851

Natanggal ko na yung lima, pero may napansin akong isang screw sa tabi ng simcard slot(yung may bilog sa picture) na natakpan ng white seal na parang papel, tinanggal ko yung seal tapos sinubukan kong tanggalin pero sobrang higpit niya, halos masira na ang ulo ng screw.

Tanong ko lang kung kasama pa ba siyang tanggalin yung may bilog sa picture para mabaklas ko yung likod o kahit hindi na? Salamat sa sasagot

mukhang nabilog mo yung screw boss.... tatanggalin lahat yan. hasain mo lang yung torx screw driver mo masusungkit pa yan

 

[hot_walker]

Band 28 700mhz supported ba to? Thank you

 

[marjun11223135]

Maraming salamat dito boss,, sa wakas na openline ku din pocket wifi ku..

 

[Zero0ooo0]

Pede ba laptop gamitin dito

 

[cl0udy]

thank you for the tutorial Sir

 

[makipogz]

Pede ba laptop gamitin dito

pwede. as long as hindi windows 10 ang OS mo

 

[markofsteel]

Yes finally pwde ko na e unlock ung kabibili kung Globe LTE. Salamat dito ts.

 

[Tommy 40588]

Thanks TS naunlock ko na Thanks din sa isang member na tumulong sakin sa pagbaklas

Kaya lang ang problema ko ngayon, di siya nag-automatic nagredirect sa Huawei Web Interface sa 192.168.8.1 , ang masaklap di ako makaconnect sa Wifi ko kasi di ko rin alam ang bagong pass nito. SSID niya HUAWEI-4050. Sinubukan ko rin yung 12345678 password ayaw rin gumana.


Ok lang kayang ireset siya gamit ang Reset button? Or baka mawala yung pagkaunlock at bumalik sa Globe simlock? Or baka mabrick yung pocket wifi (?) salamat ulit sa tutulong

 

[wimax1019]

Patatak. Ako dito

 

[Jessiemae19]

Thanks TS naunlock ko na Thanks din sa isang member na tumulong sakin sa pagbaklas

Kaya lang ang problema ko ngayon, di siya nag-automatic nagredirect sa Huawei Web Interface sa 192.168.8.1 , ang masaklap di ako makaconnect sa Wifi ko kasi di ko rin alam ang bagong pass nito. SSID niya HUAWEI-4050. Sinubukan ko rin yung 12345678 password ayaw rin gumana.


Ok lang kayang ireset siya gamit ang Reset button? Or baka mawala yung pagkaunlock at bumalik sa Globe simlock? Or baka mabrick yung pocket wifi (?) salamat ulit sa tutulong

Same case din sakin iyan sir, di ako makapasok sa portal ng Huawei pagtapos ko maunlock, pag nireset ko siya nagpupula lang ang signal, ayaw niya bumalik sa dating SSID. Pinindot ko na ng sobrang tagal yung reset button gamit ng pin pero wala pa rin talaga, ayaw magreboot. Laptop yung ginamit ko para pang-unlock.

 

[ThaBlackMumba]

Napaka husay mo brad! apir!

 

[Tommy 40588]

Same case din sakin iyan sir, di ako makapasok sa portal ng Huawei pagtapos ko maunlock, pag nireset ko siya nagpupula lang ang signal, ayaw niya bumalik sa dating SSID. Pinindot ko na ng sobrang tagal yung reset button gamit ng pin pero wala pa rin talaga, ayaw magreboot. Laptop yung ginamit ko para pang-unlock.

Ok na pala sa akin ma'am, ginawa ko lang eh sinaksak ko yung pocket wifi sa USB cable sa laptop ko then may lumabas na CD Drive ng Broadband. Irun niyo po yun at magreredirect ka na sa 192.168.8.1 matic na po yun,pwede nang maaccess si Web UI ni Huawei

Maraming maraming salamat talaga TS, malaking naitulong mo sa ating mga members!

View attachment 334693

 

[underzero123]

Gawa Naman po Kayo ng VIDEO TUTORIAL para mas maintindihan haha.

- - - Updated - - -

I finally unlocked my Huawei E5773CS-933 modem from Globe.

I've been trying to unlock it by following a guide for the E5573-609 and E5573-322. However, those did not help as the boot pin is located differently for this variant. Once I located the boot pin (by shorting out every single pin in the board, one at a time), I tried loading the generic E5573CS firmware (after running Balong USB Downloader) and would refuse to install (I get error 12). Given those obstacles, I gave up and hunted for the Globe's 933 firmware. The 933 firmware that I downloaded turned out to be an unbranded/generic, SIM unlocked firmware. From there I faced some more obstacles, mainly the WebUI and dashboard files are nowhere to be found, except on one website where you need to pay at least $15 for a paid account, to get access to the files. After pulling the trigger, I was able to unlock the device as well as remove Globe's branding in the process.

I decided to put all of the files you need in a one ZIP archive. So you won't have to spend hours searching for the files. I know you got better things to do.

Download:
E5773CS-933 Unlock
HXD Hex Editor

Also, I'm not respponsible if you screw/hard brick your modem. I've done this twice already (to unlock my modem (and then to replicate these step)

1. Install the both the FcSerialDrv and Mobile Partner drivers on "Drivers" directory.

2. Disassemble your modem using T5 torx screwdriver.
NOTE: This is the part where you'll have to break the seal and void your warranty. Sorry, there's no way to unlock without doing this. So either keep your warranty or unlock your modem.

3. Take out the board and flip it over.

4. Connect the board to the computer, and open Device Manager

5. Grab tweezers or similar device that's conductive. Then short out one of the pin/metal part (shown in the pic) near the SIM card slot.

View attachment 1235550

6. While keeping the pin/metal part shorted out. Go ahead and put the battery approximately 45-degree angle while keeping it in contacct witn the gold terminals. As shown in the pic.

View attachment 1235551

7. If you did it right. You should see "HUAWEI Mobile Connect - 3G PC UI Interface", "FC - PC UI Interface" or something similar under Ports (COM & LPT) on Device Manager. You don't need the tweezers anymore but leave the battery alone.

View attachment 1235552

If you're getting a message saying that the last USB device you have inserted can't be recognized, then try connecting using a different cable, port, or even a different computer.

8. Launch Balong USB Loader at "Balong USB Downloader" directory.

9. Click "Detect". Then Press the three dots. Then "Load"

10. It should take about 5-20 seconds for USB Downloader to do its thing. It's normal for the program to freeze, however, when its done. It should return with a full progress bar.

View attachment 1235553

11. Check Device Manager and if you see both "FC - Application Interface" and "FC - PC UI Interface" or something similar, proceed to the next step.

View attachment 1235554

12. Go to "Firmware (21.320.99.05.00)" directory and run "E5573Cs-933_Update_21.320.99.05.00.exe" The go through the wizard.

13. Go to "WebUI (WEBUI_21.100.32.00.03_NE5)" and run "Update_WEBUI_21.100.32.00.03_NE5.exe". Same thing as last step. Go through the wizard.

14. Let go of the battery, disconnect the board, and assemble the modem.

15. Insert a SIM card. (I used a Globe SIM, but any SIM could work.) DON'T SKIP THIS. Doing so will give you an error on DC Unlocker when trying to repair the serial number and IMEI of your modem.

16. Connect the modem to the computer. Then run "dc-unlocker2client_1277.exe" at the "DC Unlocker" directory.

17. Click on the magnifying glass/search.

18. When the modem is found, you'll see that it's already unlocked but we can't use it yet due to not having the correct serial and IMEI.

View attachment 1235555

19. Run HxD and type out the serial number on the right side.

20. Now type in this command: AT^NVWR=6,16,** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Replace ** with the hex code you got from HxD (copy paste the values in the middle (between the zeros and the serial number you just typed. Press enter. It should say OK.

21. Now type in this command: AT^CIMEI="*****". For example if your imei is 1234567890123456, then you would type: AT^CIMEI="123456789123456"
Replace * with your IMEI. Press enter. It should say OK.

View attachment 1235556

22. Click on the magnifying glass (again) and see if the correct serial number and IMEI shows up. Once done, close out of DC Unlocker.

23. Finally, go to "Firmware (21.326.13.00.00)" directory and run "E5573Cs-933_Update_21.326.13.00.00.exe"

One done. The modem should reboot and should automatically open a web browser, which goes to the Huawei page. If not, open your web browser and go to 192.168.8.1. If it asks you for a username and password. It's "admin" for both. From here, you'll need to setup the network name, password, etc. Just like you would when you first bought the modem.

View attachment 1235557

Take note that we don't have the Globe branding anymore.

View attachment 1235559

And for those who are wondering, 4G also works. Although, whenever I get LTE on my Sun Cellular SIM, it shows as SMART.

View attachment 1235560

TS Video Tutorial naman jan. Salamat