How to Openline (Unlock) and Debrand Huawei e5573cs-933 (Globe)

[derreck101]

may mga drivers na po ba para sa windows 10???

 

[dheck89]

Ayaw na gumana ng physical reset button at reset sa webUI after nya maunlocked, nagno-NO SERVICE lang sya kapag pinindot yung reset. Nagtry ako iflash ulit yung firmware pero wala rin. Help guyz. Thanks

 

[zoelski20]

Saan nakaka hanap ng tweezer? Wala ako yan eh

 

[dheck89]

Saan nakaka hanap ng tweezer? Wala ako yan eh http://www.symbianize.com/attachment.php?attachmentid=1235550&d=1512054220

Kahit hindi na baklasin yung device pwede. Kapain mo lang sa gilid lagayan ng SIM yung isshort mo. Gamit ka lang ng manipis na alambre or wire basta magkakasya sa butas.

 

[lastexile]

boss salamat dito naopenline ko na. hinde ko na din inopen ung sakin. salamat dun sa nagturo na di na need iopen hehe nahirapan lang ako kase nanghiram pa ko ng window7. haha
ang ginamit ko safety pin(perdible) lang wala kase ako tweezer.

 

[Khiane12]

Pahelp naman po sa hxd di ko kasi masundan yung number 19-21 eh.. newbei here. Maraming salamat po..

 

[Exlaust008]

same problem sana may makatulong nakalimutan ko pass ng admin di nako makapasok palitan ko sana password pero ayaw na din ma reset...kindly help mga sir thanks in advance

- - - Updated - - -

Ayaw na gumana ng physical reset button at reset sa webUI after nya maunlocked, nagno-NO SERVICE lang sya kapag pinindot yung reset. Nagtry ako iflash ulit yung firmware pero wala rin. Help guyz. Thanks

same problem sana may makatulong nakalimutan ko pass ng admin di nako makapasok palitan ko sana password pero ayaw na din ma reset...kindly help mga sir thanks in advance

 

[jok_virus]

TY Idol. Narealize ko lng. Kahit di pla iopen, abot nman ung mga dapat ishort out. Di ko lng sure kung kaya ng tweezer. LAN wire kasi gamit ko pang short

Gusto ko din gawin yan, kaso nakakatakot, sure kaya talaga jan banda yun? hihi, sana may mag comment na ganyan din ginawa, para hindi na need ng screw .

nagawa kuna idea nyo boss eto munting maliit na bagay , nakuha ko sa basura ko ,, twist tie wire
gawing mala letter J ,, then tusok tusok lang ...

View attachment 336516

View attachment 336517

palagay ko na gets nyo na

pag nag full bar na yung unang firmware at nag stack up sa load bar
alisin na yung battery and alis wire at then balik battery , then proceed na sa ilang step 2nd and last 3rd

 

[underzero123]

working ba kahit di na buksan ng torq scew driver?

- - - Updated - - -

nagawa kuna idea nyo boss eto munting maliit na bagay , nakuha ko sa basura ko ,, twist tie wire
gawing mala letter J ,, then tusok tusok lang ...

View attachment 1243990

View attachment 1243991

palagay ko na gets nyo na

pag nag full bar na yung unang firmware at nag stack up sa load bar
alisin na yung battery and alis wire at then balik battery , then proceed na sa ilang step 2nd and last 3rd

Pa see yung mas malapit na picture

 

[jok_virus]

working ba kahit di na buksan ng torq scew driver?

- - - Updated - - -



Pa see yung mas malapit na picture

Useless kung picturan kupa ng maige kasi lalabo pagka shoot ko better try it nalang .. tested ko naman eh .. kung magka short circuit iyan .. bayaran ko ng 1500 .. garantisado tested ko iyan

 

[underzero123]

Useless kung picturan kupa ng maige kasi lalabo pagka shoot ko better try it nalang .. tested ko naman eh .. kung magka short circuit iyan .. bayaran ko ng 1500 .. garantisado tested ko iyan

anong klaseng wire yan paps?

 

[jok_virus]

anong klaseng wire yan paps?

Twist tie wire . Nasa picture na .. back read boss

 

[harventot]

sir bat di po maopen ung file na dl ko na kasi tas pag extract ko ayaw talaga

 

[godsend21]

nagawa kuna idea nyo boss eto munting maliit na bagay , nakuha ko sa basura ko ,, twist tie wire
gawing mala letter J ,, then tusok tusok lang ...

View attachment 1243990

View attachment 1243991

palagay ko na gets nyo na

pag nag full bar na yung unang firmware at nag stack up sa load bar
alisin na yung battery and alis wire at then balik battery , then proceed na sa ilang step 2nd and last 3rd

Boss sa pag short ng pin, kailangan ba talaga dun sakto mismo sa pin katulad sa pic ni ts o kahit saan dun sa pin?

 

[dheck89]

Boss sa pag short ng pin, kailangan ba talaga dun sakto mismo sa pin katulad sa pic ni ts o kahit saan dun sa pin?

Oo kailangan sakto dun.

 

[lloydmark13]

I finally unlocked my Huawei E5773CS-933 modem from Globe.

I've been trying to unlock it by following a guide for the E5573-609 and E5573-322. However, those did not help as the boot pin is located differently for this variant. Once I located the boot pin (by shorting out every single pin in the board, one at a time), I tried loading the generic E5573CS firmware (after running Balong USB Downloader) and would refuse to install (I get error 12). Given those obstacles, I gave up and hunted for the Globe's 933 firmware. The 933 firmware that I downloaded turned out to be an unbranded/generic, SIM unlocked firmware. From there I faced some more obstacles, mainly the WebUI and dashboard files are nowhere to be found, except on one website where you need to pay at least $15 for a paid account, to get access to the files. After pulling the trigger, I was able to unlock the device as well as remove Globe's branding in the process.

I decided to put all of the files you need in a one ZIP archive. So you won't have to spend hours searching for the files. I know you got better things to do.

Download:
E5773CS-933 Unlock
HXD Hex Editor

Also, I'm not respponsible if you screw/hard brick your modem. I've done this twice already (to unlock my modem (and then to replicate these step)

1. Install the both the FcSerialDrv and Mobile Partner drivers on "Drivers" directory.

2. Disassemble your modem using T5 torx screwdriver.
NOTE: This is the part where you'll have to break the seal and void your warranty. Sorry, there's no way to unlock without doing this. So either keep your warranty or unlock your modem.

3. Take out the board and flip it over.

4. Connect the board to the computer, and open Device Manager

5. Grab tweezers or similar device that's conductive. Then short out one of the pin/metal part (shown in the pic) near the SIM card slot.

View attachment 1235550

6. While keeping the pin/metal part shorted out. Go ahead and put the battery approximately 45-degree angle while keeping it in contacct witn the gold terminals. As shown in the pic.

View attachment 1235551

7. If you did it right. You should see "HUAWEI Mobile Connect - 3G PC UI Interface", "FC - PC UI Interface" or something similar under Ports (COM & LPT) on Device Manager. You don't need the tweezers anymore but leave the battery alone.

View attachment 1235552

If you're getting a message saying that the last USB device you have inserted can't be recognized, then try connecting using a different cable, port, or even a different computer.

8. Launch Balong USB Loader at "Balong USB Downloader" directory.

9. Click "Detect". Then Press the three dots. Then "Load"

10. It should take about 5-20 seconds for USB Downloader to do its thing. It's normal for the program to freeze, however, when its done. It should return with a full progress bar.

View attachment 1235553

11. Check Device Manager and if you see both "FC - Application Interface" and "FC - PC UI Interface" or something similar, proceed to the next step.

View attachment 1235554

12. Go to "Firmware (21.320.99.05.00)" directory and run "E5573Cs-933_Update_21.320.99.05.00.exe" The go through the wizard.

13. Go to "WebUI (WEBUI_21.100.32.00.03_NE5)" and run "Update_WEBUI_21.100.32.00.03_NE5.exe". Same thing as last step. Go through the wizard.

14. Let go of the battery, disconnect the board, and assemble the modem.

15. Insert a SIM card. (I used a Globe SIM, but any SIM could work.) DON'T SKIP THIS. Doing so will give you an error on DC Unlocker when trying to repair the serial number and IMEI of your modem.

16. Connect the modem to the computer. Then run "dc-unlocker2client_1277.exe" at the "DC Unlocker" directory.

17. Click on the magnifying glass/search.

18. When the modem is found, you'll see that it's already unlocked but we can't use it yet due to not having the correct serial and IMEI.

View attachment 1235555

19. Run HxD and type out the serial number on the right side.

20. Now type in this command: AT^NVWR=6,16,** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Replace ** with the hex code you got from HxD (copy paste the values in the middle (between the zeros and the serial number you just typed. Press enter. It should say OK.

21. Now type in this command: AT^CIMEI="*****". For example if your imei is 1234567890123456, then you would type: AT^CIMEI="123456789123456"
Replace * with your IMEI. Press enter. It should say OK.

View attachment 1235556

22. Click on the magnifying glass (again) and see if the correct serial number and IMEI shows up. Once done, close out of DC Unlocker.

23. Finally, go to "Firmware (21.326.13.00.00)" directory and run "E5573Cs-933_Update_21.326.13.00.00.exe"

One done. The modem should reboot and should automatically open a web browser, which goes to the Huawei page. If not, open your web browser and go to 192.168.8.1. If it asks you for a username and password. It's "admin" for both. From here, you'll need to setup the network name, password, etc. Just like you would when you first bought the modem.

View attachment 1235557

Take note that we don't have the Globe branding anymore.

View attachment 1235559

And for those who are wondering, 4G also works. Although, whenever I get LTE on my Sun Cellular SIM, it shows as SMART.

View attachment 1235560

TY for sharing bro and GOD BLESS

 

[ricjmanarang]

bkt po lagi corrupted ung file naka 3 download na po ako (https://mega.nz/#!aJBw0ZBK!hm_9DGcwXqyseofevVbnuo4pRLDmIMVGTWXlm0WpSjk)

 

[Silvestreli]

Wow sir maraming salamat rate perfect 10
Diko na ginamita ng tweaser hirap nabibitawan sinolda ko nlang ng wire
Pero. Galing tlaga boss salamat now anlakas na net ko sa smart di nako nag titiis sa globe mahina kasi samin

 

[ricjmanarang]

pwd po pa reupload ng file for firmware, curropted po kasi ung nasa mega

 

[LeaRyl]

ggmit kb ng usb cable dito pwse b sa window 10