B593s-931 Nov: may Pag-asa bah o Wala.?

[AldRezaine]

sure po ba????

Sure yan bro, just follow exactly the instructions..

 

[carrerayukieto]

Boss patulong baka may idea ka ung b593u-91 ko ayaw ng gumana pero naka ilaw lang palagi ang power indicator kung baga ayaw ng mag fully load..tanong ko lang kung posibli pa ba gumana ulit? kahit mag direct port ka gamit RJ45 wala rin connection.. sala mat pag may ma e share kang idea boss

 

[devzdust]

Boss patulong baka may idea ka ung b593u-91 ko ayaw ng gumana pero naka ilaw lang palagi ang power indicator kung baga ayaw ng mag fully load..tanong ko lang kung posibli pa ba gumana ulit? kahit mag direct port ka gamit RJ45 wala rin connection.. sala mat pag may ma e share kang idea boss

try mo mag install nang firmware nyan boss gamit ka nang multicast bakasakaling gumana pa

 

[tanatej]

ito na solution sa bricked na 931 natin

The fix

The prerequisite for the fix is, that you are logged into your B593 s-22 via SSH and are able to run lteat and get sensible response out of it. Example (the blank lines happen on my SSH, I don't know why):
# lteat
AT>ati

i

Model: B593s-22

Revision: V200R001B180D20SP05C260

IMEI: 860091028600910

+GCAP: +CGSM,+DS,+ES

OK
AT>
Then you're good to go.
First confirm, that you are in the equipment mode:
AT>at ^nvrd=52110
^NVRD: 12,31 00 00 00 00 00 00 00 00 00 00 00
OK
That's a ReaD-command for NVRAM address location 52110. To change the mode back to normal, a WRite needs to be issued:
AT>at ^nvwr=52110,1,0
OK
Confirm the result:
AT>at ^nvrd=52110
^NVRD: 12,00 00 00 00 00 00 00 00 00 00 00 00
OK
Notice how the hex value 0x31 is changed to 0x00. Btw. if you look at the ASCII-table, you may notice, that 0x31 stands for number 1. That's would be similar to the (1) in g_Equip_Mode_value = 1.
Now all you have to do is power-off your box and kick it back on.


Credits to


Hacker's ramblings

Meron bang translation nito para sa mga di gaano bihasa sa telnet?

 

[carrerayukieto]

try mo mag install nang firmware nyan boss gamit ka nang multicast bakasakaling gumana pa

try ko boss magpasok ng firmware..kaso lang undetected kasi ang modem dead ata talaga pero subukan ko mag usb.. pag port kasi gamit wala talaga undetected ung modem.. salamat s advice

 

[devzdust]

try ko boss magpasok ng firmware..kaso lang undetected kasi ang modem dead ata talaga pero subukan ko mag usb.. pag port kasi gamit wala talaga undetected ung modem.. salamat s advice

mag flash ka muna nang FW para sa modem mo boss tignan mo kong papasok..

 

[tiancris]

@devzdust
thanks po. unbrick na na modem ko!!!

 

[tribalseedz]

sana may update na para ma unlock na

 

[r1bnc]

unlocking nalang kulang ...

 

[devzdust]

unlocking nalang kulang ...

next naman sana is unlocking.. baka sa AT command pwede ma unlock ang modem..
hindi ko na kc ma brick ung modem ko para mapasok ang AT command.. para don pag aralan ulit kong pwede..

 

[at0m]

start again with this AT command-->AAT^cardlock?

 

[mick0p0tx]

okay na yung modem ko na ubrick na.
using

AT^SFM=1 - factory mode
AT^RESET - reboot modem

tinry ko din to
# lteat
AT>ati

i

Model: B593s-22

Revision: V200R001B180D20SP05C260

IMEI: 860091028600910

+GCAP: +CGSM,+DS,+ES

OK
AT>
Then you're good to go.
First confirm, that you are in the equipment mode:
AT>at ^nvrd=52110
^NVRD: 12,31 00 00 00 00 00 00 00 00 00 00 00
OK
That's a ReaD-command for NVRAM address location 52110. To change the mode back to normal, a WRite needs to be issued:
AT>at ^nvwr=52110,1,0
OK
Confirm the result:
AT>at ^nvrd=52110
^NVRD: 12,00 00 00 00 00 00 00 00 00 00 00 00
OK

tapos napasok ko din admin kaso nung narestart ko na yunh modem hindi ko na sya napasok sa admin pero unbrick na sya.
nagupload ako via local host ayaw maupdload ndi maverify

 

[marktattoo]

Unlock Modem VIA AT^Command

at ^ cardlock = "unlock code"
unlock code is your calculated code

baka eto ung pang unlock?

 

[tribalseedz]

Unlock Modem VIA AT^Command

at ^ cardlock = "unlock code"
unlock code is your calculated code

baka eto ung pang unlock?

Di working na try ko na yan nung bricked pa model ko

 

[marktattoo]

Di working na try ko na yan nung bricked pa model ko

yung at para sa 936 na pang unlock natry mo?

 

[elvinabella]

Still working parin ako.... kaya ko yan inilabas para lahat may idea....
Wala ako sinasabi na iba pa sa mga post ko.... Kaya hintay hintay lang
ilalabas ko ito lahat, hindi ganun kadali ang gumawa ng mga ganito
kaya intay lang kayo atleast ngayon may firmware na na para sa Nov,
tulungan nalang....

Kung ipagpapatuloy niyo parin ang pang babash malamang hindi ito
matuloy na imbes na magagawa at maibahagi sa lahat..

Kaso karamihan dito panay paninira kung ano ano hindi nalang
magsabi na TY...

tama ka TS tayo tayo na nga lang dapat magtulungan, tayo tayo pa nag.aaway.... di kasi mawala ang inggit sa mga kupal na yan eh....

 

[marktattoo]

tama ka TS tayo tayo na nga lang dapat magtulungan, tayo tayo pa nag.aaway.... di kasi mawala ang inggit sa mga kupal na yan eh....

may naitulong ba yang ts mo nag yabang lang yang kupal na yan tas biglang nawala

 

[tribalseedz]

busybox at vi nlng pag asa natin sa 931

 

[jomons]

busybox at vi nlng pag asa natin sa 931

tama boss!!! sakin ok na back to normal narin.. admin access na pero dparin openline..

 

[moleparadox]

https://blog.hqcodeshop.fi/categories/7-Huawei-B593 D2 KO MA INTINDIHAN TONG POST NILA