(Help) Huawei B315s-936 Red Signal Problem after a year na paggamit

[drunkier]

ask ko lang kung may fix ba yun 936 na nag red light kahit anong sim ang ilagay?

nangyari kasi bigla sa 936 ko ng di ko inaasahan, di naman ganito dati, isang taon ko nang gamit to simula ng na-debrand at na-full admin access.. naisip ko tuloy baka nablocked na ng globe itong modem.. sana may fix pa..

naka auto na rin ang network mode pero ganun pa din..

thanks..

 

[nynjalee]

ask ko lang kung may fix ba yun 936 na nag red light kahit anong sim ang ilagay?

nangyari kasi bigla sa 936 ko ng di ko inaasahan, di naman ganito dati, isang taon ko nang gamit to simula ng na-debrand at na-full admin access.. naisip ko tuloy baka nablocked na ng globe itong modem.. sana may fix pa..

naka auto na rin ang network mode pero ganun pa din..

thanks..

yung sa akin ok pa kahapon ngayun red ang signal at imposible naman na mablock dahil one week ko pa lg nabili yung sim, naexpire kasi yung old sim ko dahil di ko nalodan ng matagal.

 

[tweak97]

no sim card detected po ang problem nyo? or no signal?

 

[kenth]

Got the same problem. I have two modems, one of them has no more signal after a blackout.

I tested the sim in another modem and the sim is ok.

 

[rockie17]

ganyan din problem ko ayaw sa lte kaya red mode try nyo sa hspa+ gumana sya may signal naman ng lte pero failed pag nai-connect ko paano kaya ito tiis muna sa 3g..

 

[jazzyjenner]

ask ko lang kung may fix ba yun 936 na nag red light kahit anong sim ang ilagay?

nangyari kasi bigla sa 936 ko ng di ko inaasahan, di naman ganito dati, isang taon ko nang gamit to simula ng na-debrand at na-full admin access.. naisip ko tuloy baka nablocked na ng globe itong modem.. sana may fix pa..

naka auto na rin ang network mode pero ganun pa din..

thanks..

Same problem, naayos mo pa ba?

 

[janex91]

Same Problem, bigla nalang nag Red Tide simula nung nag insert ako ng Smart Sim. Connected sa 2G , sa 3G naman Need pa antenna pra magka Signal, pero Sa LTE No Service talaga kahit malakas naman sa Area ko ang 3G/4G Both smart & Globe..naka Ilang Flash na aq ng Ibat ibang FW , Re Open Line w/ CID Reader pero waley pa rin...Tapon ko nalang ata to hahaha

 

[rusyl2]

kakaayus ko lang ng ganitong problema haha

- - - Updated - - -

andito lang din po ang solution

 

[peeween]

nkaka takot to ah.. lalo na ako nagbebenta ng 936..

 

[Mikey Kun]

di kaya sa area problem yan??

 

[janex91]

kakaayus ko lang ng ganitong problema haha

- - - Updated - - -

andito lang din po ang solution

Panu paps? Pa Share naman po

- - - Updated - - -

di kaya sa area problem yan??

Hindi rin paps..may S22 at pocket wifi ako sa bahay wla naman problema sa signal

 

[percivalmipa]

langya ganun din sakin nag red light bigla pinalitan ko ng sim ganun parin...

 

[jomons]

sakin sim detected globe at smart.. may signal lte at 3g, ang problema wan disconected.. na try ko na lahat ng procedure walang epic..

 

[riokulit09]

madali lang yan gawin palit ka ng firmware

Question :

Can I change to any firmwares available in this forum?
a : Yes you can, currently using mine with modified 21.321.03.01.973 Firmware installed.


Prerequisites :
Metal conductor for jumping BOOT and GND pin on the board.
Files required for doing this tutorial. (Firmware, balong_flash, and usbdloader.bin)

Procedure :

Contact BOOT and GND pin, and then plug the Power Adapter to the modem. If the Power Light lit after connecting the Power Supply, repeat the steps. If not, then proceed to the next step.
Click image for larger version.

Name: 35ksrjs.jpg
Views: 897
Size: 425.3 KB
ID: 1210092
Reference Picture of BOOT pin.

Connect USB Male to Male Cable to the Modem and to your Computer, It should show a COM PORT of HUAWEI Mobile Connect - 3G PC UI Interface.

Run commitblocks.cmd, and select option number 1.

Fastboot should respond to the Command Prompt with "OK" status, if it respond with a "FAIL" status. Repeat the steps.

After deleting nvram image of your modem, turn it off then repeat the first step above for jumping BOOT and GND pins.

Once you get to work the BOOT and GND pin again and it shows a HUAWEI Mobile Connect - 3G PC UI Interface COM PORT at Device Manager.

Run load_usbdloader.cmd. The script will automatically load usbdloader to the modem, once finished it will show a new COM PORT named HUAWEI Mobile Connect - 3G Application Interface on Device Manager.

Run B315s-22_Update_21.311.05.00.00_M_01.01_nvr.exe and click Start. When the Firmware Upgrader Program found the COM PORT of your device, device LED lights will lit up. Wait until the Firmware Upgrader completes downloading the software to your modem, and also wait for the modem to reboot itself.

Once you finish flashing the firmware to your modem, unplug the USB Male to Male cable then do a power cycle to your device (Unplug and replug the power adapter)

Plug LAN Cable to your modem and go to 192.168.8.1, if a Generic WEBUI of Huawei shows up. Congratulations, you've just successfully revived your modem from "death".

 

[jomons]

madali lang yan gawin palit ka ng firmware

Question :

Can I change to any firmwares available in this forum?
a : Yes you can, currently using mine with modified 21.321.03.01.973 Firmware installed.


Prerequisites :
Metal conductor for jumping BOOT and GND pin on the board.
Files required for doing this tutorial. (Firmware, balong_flash, and usbdloader.bin)

Procedure :

Contact BOOT and GND pin, and then plug the Power Adapter to the modem. If the Power Light lit after connecting the Power Supply, repeat the steps. If not, then proceed to the next step.
Click image for larger version.

Name: 35ksrjs.jpg
Views: 897
Size: 425.3 KB
ID: 1210092
Reference Picture of BOOT pin.

Connect USB Male to Male Cable to the Modem and to your Computer, It should show a COM PORT of HUAWEI Mobile Connect - 3G PC UI Interface.

Run commitblocks.cmd, and select option number 1.

Fastboot should respond to the Command Prompt with "OK" status, if it respond with a "FAIL" status. Repeat the steps.

After deleting nvram image of your modem, turn it off then repeat the first step above for jumping BOOT and GND pins.

Once you get to work the BOOT and GND pin again and it shows a HUAWEI Mobile Connect - 3G PC UI Interface COM PORT at Device Manager.

Run load_usbdloader.cmd. The script will automatically load usbdloader to the modem, once finished it will show a new COM PORT named HUAWEI Mobile Connect - 3G Application Interface on Device Manager.

Run B315s-22_Update_21.311.05.00.00_M_01.01_nvr.exe and click Start. When the Firmware Upgrader Program found the COM PORT of your device, device LED lights will lit up. Wait until the Firmware Upgrader completes downloading the software to your modem, and also wait for the modem to reboot itself.

Once you finish flashing the firmware to your modem, unplug the USB Male to Male cable then do a power cycle to your device (Unplug and replug the power adapter)

Plug LAN Cable to your modem and go to 192.168.8.1, if a Generic WEBUI of Huawei shows up. Congratulations, you've just successfully revived your modem from "death".

nagawa ko na yan bos no effect parin.. lahat ng firmware na try ko na.. sa basurahan talaga ang punta nitong turtogok na 936 nato..

 

[janex91]

nagawa ko na yan bos no effect parin.. lahat ng firmware na try ko na.. sa basurahan talaga ang punta nitong turtogok na 936 nato..

Hardware na yan Paps..nabagsak mo ba yang Modem mo? try mo kabitaan ng Antenna at i lock mo sa 3G if magkaka signal ba

 

[riokulit09]

meron technic dyan para mapagana yan na 936 mo na power led only lang

 

[percivalmipa]

mga paps ok na yung 936 ko mukhang nag update lang si globo nung nakaraan kaya nagpula signal pinahinga ko muna kasi ng ilang araw ang 936 ko nung nag pula signal cp lang gamit kong hotspot pag lagay ko ng sim sa 936 ko kanina at in-on ko nag green light na signal ok na sya...

 

[ReymarkRosales]

nagawa ko na yan bos no effect parin.. lahat ng firmware na try ko na.. sa basurahan talaga ang punta nitong turtogok na 936 nato..

change imei

 

[6thokage]

change imei

pano mag change imei?

- - - Updated - - -

nagawa ko na yan bos no effect parin.. lahat ng firmware na try ko na.. sa basurahan talaga ang punta nitong turtogok na 936 nato..

tinapon mo na boss? di na talaga naayos?