B315s-936 power light only solution

[gltimbreza]

Tuts for B315s-936 power light only.
*Basahin lahat muna bago simulan.. may mga revisions.

working lang on following conditions:

1. Successful sa new openline ng 936 pero after ng reset e powerlight pa rin.
2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD.

Kung hindi mo naabot yung "Done/Remove battery and put it again" bka hindi gumana.

Steps:

Note: Reported po na mas successful pag gawin muna yung new 936 flashing by sir Jansen Ramos.
http://www.symbianize.com/showthread.php?t=1371603
Mostly lahat nang successful e ginamit Win7 64bit OS.

1. Hard reset, either :

a. press power button at reset button then plug power, pag umilaw yung red, wag bitawan hanggang hindi nawawala ynug red.
b. pag hindi umilaw yung red, press power at wps buttons, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
​

2. Hintayin umilaw blue light at last two signal bars. wag galawin.
3. Hintayin umilaw red light at first and last signal bars. wag galawin.
4. Hintayin na power light na lang. plug usb to usb cord.
5. Check sa device drivers dapat may unknown o Android ADB Interface ka.
6. Ipilit and driver na - Android ADB Interface, mag have disk ka. piliin mo yung nasa folder adb_driver_windows
7. Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"

Dapat yung cmd mo "c:\files>"​

8. Sa CMD, type

fastboot -i0x12d1 getvar product

9. Dapat may magpakita na - product: balongv7r2

10. Sa CMD ulit, type

fastboot -i0x12d1 erase nvimg

11. Dapat may response na "OK".

12. Sa CMD ulit, type

fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin

13. Dapat may response na "OK".

14. Reboot na

b315s-936_for_powerlight_only.rar
Additional files http://www.mediafire.com/file/w75a9mn87m2pitp/tools.rar

Source: 4pda.ru

win 8.1/10 os patch:
http://www.mediafire.com/file/8etvc0u6gzo4608/USB_NOT+RECOGNIZE+FIX_jansen.reg
credits to sir jansen ramos

Second trick to try,
Pero start with the needle trick,
(shorted debug pins, then plug power, plug usb, no powerlight but detected as 3G PC UI interface)
Instructions inside.
fix2b315.rar
*try at you're own risk sa second trick kasi lahat ng result e deadboot, pero you can always go back to power led only using new 936 flashing.

Source link kung gusto nyo magbasa.. google translate na lang
http://4pda.ru/forum/index.php?showtopic=700481&st=680

Middle East firmware credits to Sir rexzero
http://www.symbianize.com/showthread.php?t=1393606&p=22514169&viewfull=1#post22514169

Zain Firmware credits kay Sir mulot
https://www.mediafire.com/?371hp9w4j9veb3f

gamit ka windows 7 64 bit boss.
install lahat drivers tapos restart pc muna.
tapos sundan mo ung steps ni sir l2aizen :

1.ung method ni jansen Ramos
pero ang ifflash ay ung files na ay ung nasa inilink ni sir rexzero
https://www.mediafire.com/?78ytzt91jtclu6n
pag natapos mona iflash (done remove baterry blahblah)remove power,usb
rekta kana sa tut ni sir gltimbreza



2.ung method ni sir gltimbreza
Dagdag tips ko lng to .
(wag mo muna buksan cmd pag katapos mo sundan step 1-6.
katapos sa step 6 try mo run as admin ang cmd pag ayaw parin try mo normal na cmd. tapos sa step 7 kana. ganito lng ginawa ko tapos nag ok nako sa step 10.)

Mga bos pag nagflash kau ng middle east fw kahit di nyo na sundan yung 1-4 ni ts, direstso na agad kau sa step 5 then cmd na.

sa mga bagong mag try,

try nyo muna wag mag "fastboot -i0x12d1 erase nvimg"

bali ganito lang muna gawin nyo

1.fastboot -i0x12d1 getvar product
2.fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin
3.fastboot reboot

pumapasok naman kasi kahit wala yun "fastboot -i0x12d1 erase nvimg" baka kasi dito ang dahilan bakit di na tayo makapag flash ng ibang firmware dahil erase na yun nvimg natin,

sa orig instruction kasi, last option na yun "fastboot -i0x12d1 erase nvimg" kung same pa rin ang status after mag "fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin"

stuck sa polko yun nagawa ko kagabi

Eto na Video ko

click settings sa video at set 720p

 

[lex71]

Paano po gawin ang step na ito?
Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"

 

[gltimbreza]

Paano po gawin ang step na ito?
Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"

extract mo na lang sa c:\ drive mo.. then.. sa cmd command mo e

 cd \files

tapos check mo bago ka magrun ng commands e nsa c:\files> ka

 

[lex71]

View attachment 295522
I got this error message after typing fastboot -i0x12d1 getvar product . then correct po ba yung loaction sa files?

 

[gltimbreza]

View attachment 1168921
I got this error message after typing fastboot -i0x12d1 getvar product . then correct po ba yung loaction sa files?

wait lang sir.. kulang yung files..

- - - Updated - - -

http://www.mediafire.com/file/w75a9mn87m2pitp/tools.rar

dagdag mo bro..

 

[lex71]

2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD

sana may pag asa pa ang 936 ko, qualified po siya sa number 2.

Then tapos na po ako sa number 6.

 

[jmarprinz]

Dapat may video tutorial para madali masundan mga newbie

 

[gltimbreza]

2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD

sana may pag asa pa ang 936 ko, qualified po siya sa number 2.

Then tapos na po ako sa number 6.

dapat bro ok pati yung 1, either kasi sira na tlga nvram mo o marked as dirty lang. modified bootloader yan para iignore yung mark. dagdag mo yung new files sa files folder.. tama yung ginawa mo, yung files ko ang may kulang..

 

[lex71]

View attachment 295527
These are the errors bro. added na po yung files. Any hope?

 

[gltimbreza]

View attachment 1168933
These are the errors bro. added na po yung files. Any hope?

nghard reset kaba bro? kasi ganyan yung error ko kapag hindi ko siya hard reset, from power on lang gnyan.. flash ka ng new 936 openline, 'yung babaklasin mo tpos mgfflash ka. pag nkapagflash ka ng walang error, saka mo gawin yung steps ko. kung may error ka sa flashing, sira na nvram mo tlga.

 

[lex71]

Yes hard reset na po, I'll try again, dalawang 936 ko ang power button na lang. yung isa kahit as Android device hindi na ma-detect. One year and a half lang lifespan ng aking dalawang old model 936.

 

[gltimbreza]

wag ka maghuhugot ng power bro.. hintayin mo lang sia na magreset.

 

[lex71]

tried ko na lahat bro...thanks sa pag upload, may natutunan din ako.

 

[bentamax]

View attachment 295577

gento lumilitaw sakin

 

[christianoleamondrago]

bro thanks sa tutorial.. Hanggang blue light lang ako at signal eh. Wala na lumabas na red?

 

[gltimbreza]

View attachment 1169002

gento lumilitaw sakin

ano os mo sir? 64bit win7 gamit ko.. hanapin mo yung .reg na patch ni sir jansen ramos.. wait lang post ko link nya sa header..

- - - Updated - - -

heto link sir.. http://www.mediafire.com/file/8etvc0u6gzo4608/USB_NOT+RECOGNIZE+FIX_jansen.reg

credits kay sir jansen ramos.

- - - Updated - - -

bro thanks sa tutorial.. Hanggang blue light lang ako at signal eh. Wala na lumabas na red?

natry mo na to bro kahit yung una lang? to check na ok yung nvram mo, hindi marked as bad lang. kasi dapat yung two conditions sa first post e na-meet.
http://www.symbianize.com/showthread.php?t=1371603
credits to sir jansen ramos ulit.

 

[l2aizen]

Tuts for B315s-936 power light only.

working lang on following conditions:

1. Successful sa new openline ng 936 pero after ng reset e powerlight pa rin.
2. Unknown device sa Device manager - details - Hardware IDs - VID_12D1&PID_36DD.

Kung hindi mo naabot yung "Done/Remove battery and put it again" bka hindi gumana.

Steps:

1. Hard reset, either :

a. press power button at reset button then plug power, pag umilaw yung red, wag bitawan hanggang hindi nawawala ynug red.
b. pag hindi umilaw yung red, press power at wps buttons, pag umilaw yung red, wag bitawan hanggang hindi nawawala yung red.
​

2. Hintayin umilaw blue light at last two signal bars. wag galawin.
3. Hintayin umilaw red light at first and last signal bars. wag galawin.
4. Hintayin na power light na lang. plug usb to usb cord.
5. Check sa device drivers dapat may unknown o Android ADB Interface ka.
6. Ipilit and driver na - Android ADB Interface, mag have disk ka. piliin mo yung nasa folder adb_driver_windows
7. Go to run then CMD. - Change ka sa directory kung saan mo inextract yung files - "CD c:\files"

Dapat yung cmd mo "c:\files>"​

8. Sa CMD, type

fastboot -i0x12d1 getvar product

9. Dapat may magpakita na - product: balongv7r2

10. Sa CMD ulit, type

fastboot -i0x12d1 erase nvimg

11. Dapat may response na "OK".

12. Sa CMD ulit, type

fastboot -i0x12d1 flash fastboot fastboot-b315-baderase.bin

13. Dapat may response na "OK".

14. Reboot na

b315s-936_for_powerlight_only.rar
Additional files http://www.mediafire.com/file/w75a9mn87m2pitp/tools.rar

Source: 4pda.ru

win 8.1/10 os patch:
http://www.mediafire.com/file/8etvc0u6gzo4608/USB_NOT+RECOGNIZE+FIX_jansen.reg
credits to sir jansen ramos

sir paano po ung nasa step 6?

 

[gltimbreza]

punta ka sa control panel, tapos device manager.. hanapin mo yung unknown device mo tapos update driver.. piliin mo install drivers manually.. then have disk.. tapos piliin mo na Android adb interface. search mo google meron yn..

unknown device - right click - properties - update driver

 

[D0N0tDisturb]

TS..gawan mo ng vid.TIA!

 

[l2aizen]

Sir Maraming Salamat at Buhay Na Sya

View attachment 295603