boss pano kapag nakalagay no devices pagkaclick ko nung download emmc?
be sure po na detected na ng pc si flare mo boss para makita ng app at dl na din kau ng driver para jan
- - - Updated - - -
jtag po ang makakabuhay ng phone mo at di yan mkukuha sa mga free tools lang.....
haha tested ko po yan dahil nakapagrevive na ako ng flare 2.0 deadboot mismong phone ko pa
- - - Updated - - -
TS ako cm flare s100 hard brick yta ngyari biglang nmatay hndi n maopen detected p sa pc nagtry n din ako ng procedure n pist mo pero result still bricked p dn. Mttlungan m b ko maayos. Tnx
What you need:
1. 32-Bit PC (Vista, 7, 8, 8.1)
2. Qualcomm Product Service Tool (QPST) Link: ht t p://adf .ly/kmWqL
3. Jellybean 4.1.2 Update (Includes ALL OF THE TOOLS YOU NEED)
*Flare Device Drivers - h t tp://ad f . ly/kmXpl
*Qualcomm Modem Tools (aka IMEI Writer) - h tt p://a df. ly/kmcmO
*EMMC Download Tool - ht tp://a df. ly/kmchV
*Qualfast - ht tp://a df. ly/krPu0
*AIO Flasher (alternative to Qualfast) - ht tp://ad f.ly /krQ15
*Stock ROM (aka AP Firmware) - ht tp://a df.l y/ksNKR
*BP Firmware -
http://a df. ly/krQ68 4. Deadboot Flare5. Good, Short USB Cable (Better to avoid data loss)
INSTRUCTIONS:
1. Extract all contents of Jellybean 4.1.2 update. (AP firmware, BP firmware, Plug-ins, Flashtools & Drivers)
2. Plug deadboot flare into PC.
3. Press Windows + R, then type devmgmt.msc. The deadboot device must show as Unkown Device(with a yellow triangle and an ! sign) or Qualcomm HS-USB Android DIAG 901D (COM #)
4. If in case Qualcomm HS-USB Android DIAG 901D (COM #) has an ! sign, right click on it, then select "Update Driver Software." Click "Browse my Computer for driver software" then browse for the drivers folder. Let the driver install (Install this driver software anyways) and then close the window.(WARNING: IF IN CASE THE DEVICE DOESN'T SHOWS UP IN DEVICE MANAGER, SORRY BUT BRING IT TO A RELIABLE TECHINICIAN FOR JTAGGING) 5. Install QPST, then open eMMC Software Download (Run this as an Administrator or else you will get the error "Failed to connect to QPST server").
6. Press BROWSE, it will detect your phone. Look for the PHONE TAB that says DOWNLOAD. Press OK.
7. Under FLASH PROGRAMMER FILENAME, enter MPRG8X25.hex
8. Under BOOT IMAGE, enter 8X25_msimage.mbn
9. Press LOAD XML DEF > browse to your extracted BP Firmware > select rawprogram0 > press OPEN.
10. Press LOAD PATCH DEF > browse to your extracted BP Firmware > select patch0 > press OPEN.
11. Press DOWNLOAD. Wait PATIENTLY. Don't Panic.
12a. If on flare screen shows up "RESET FOR ENTRY QPST DOWNLOAD" or the capacitive buttons started to blink. Congratulations! Your flare is on halfway to revival! If capacitive buttons are blinking, charge your phone first then proceed.
12b. If on the eMMC Software Download shows "Error downloading image. Cookie 'if present' not received" try this:
*Press Qfuse.
*Browse to MRPG8X25.hex inside BP FIRMWARE
*Send to phone
*If succeed, go back to step 11.
-If it still fails, sorry but you need to bring it to a reliable technician ()
13. Go to flashtools folder, open EMMC (run as admin, as always). Click SELPATH, the browse to the extracted BP Firmware, then press OK. Press download and wait for the process to succeed.
14. Remove the battery of your flarem bring it back, then boot to fastboot by pressing power + volume up.
15. Go to flashtools folder, open Qualfast (run as admin!). Click Selpath, the browse to the extracted AP firmware. Wait for the bars to turn blue, then press OK. Wait for the top blue bar to turn yellow then wait for it to turn green.
16. Close all open flashtools, remove the usb cable, remove the battery, bring it back, then turn on your flare.
17. Congrats! Your flare is now revived.
Signal problems? Refer to my tutorial here:
http://ad f.l y/kmWyB
