Greetings Symbianize!
this is my first time to post a tutorial... sana po magustuhan niyo..
pasensya na sa English carabao ko at sa medyo hindi maintindihang tutorial...
!!Warning/Disclaimer!!
By reading/doing this tutorial/project..
I am not responsible to the ones who injured/harmed by this project.. so do this at your own risk..
this is for educational purpose only..
by doing this your agreeing to use it only for "paingay lang" and not to point this on any living things/creature and nothing to put any objects inside the canon that can harm anybody...
P.S.
Hindi rin ako responsable sa mga mahuhuli ng otoridad na gumagamit nito.. alam natin na ipinagbabawal ito dahil may mga taong ginagamit ito para makasakit ng kapwa nila..
NOW LETS GET INTO IT.
The tutorial is TAGLISH.. medyo hindi pa ako masyadong fluent sa English.. but I'm working on it para maging fluent ako...
nandito ako para mag share ng tutorial kung papaano gumawa ng modern canon/boga for the coming new year celebration.
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
here's the things what you'll be needed.
1. 86CM 3" PVC PIPE (COLOR ORANGE)
2. PVC PIPE 3" CAP w/ THREAD
3. TIN CAN YUNG DEL MONTE PINEAPPLE JUICE *YUNG READY TO DRINK* (NOT ALUMINUM CAN)
4. SOLID COATED COPPER WIRES (ginamit kong wire eh yung sa UTP cable
)
5. LPG LIGHTER *Yung mahabang lighter para sa kalan.
6. PVC CEMENT/SOLVENT
7. GLUE GUN AND GLUE STICK
8. RIVET BULLETS AND RIVET PUNCHER
9. CABLE ZIP TIEs *para hindi umalog ang igniter*
10. ELECTRICAL/MANUAL DRILL "para pambutas :you don't say :3"
*OPTIONAL*
10. SAND PAPER AND AEROSOL PAINTS for PIMPING YOUR BOGA!
PROCEDURE:
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
PART I.
Preparing the tincan that to be placed inside the PVC PIPE
1. Get the tin can.. turn it upside down.. (the part where the Manufactured date/BBF date indicates)
as you can see there there a Circle in the center of it...
like this..
http://i42.tinypic.com/jzebk4.jpg
butasin mo po yan color blue part
2. on the other side of the can... (the top/part where the opener/pop-up tab placed)
butasin mo po yung part kung saan naka embossed...
follow this..
http://i42.tinypic.com/30ucls8.jpg
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
GEMINI96
PART II.
PREPARING THE PIPE
as I said the PIPE has a length of 86CM
*Mag-ingat sa part na ito... maari kayong mapaso, mas maganda kung may katulong kayo sa paggawa ng part na ito.
1. Mag sukat ng 9 Inches mula sa dulo ng pipe.. kahit anong dulo pwede..
http://i40.tinypic.com/wlu9u0.jpg
2. Painitin hanggang sa medyo lumambot ang Pipe
3. Ihanda ang tin can na binutasan nyo kanina.. yung nasa PART I. ng tutorial
4. Ipasok ang tincan sa PIPE. *upside down mo sya ipapasok so it means na mauuna yung may pop-up tab side bago yung ilalim..
NOTE:
yung 9 inches na sinukat kanina.. hanggang doon mo lang ilalagay ang Tincan...
follow this...
http://i40.tinypic.com/wlu9u0.jpg
http://i43.tinypic.com/iwowif.jpg
http://i42.tinypic.com/353qh.jpg
5. pagkatapos ilagay ang tin can, ang pipe cap w/ thread naman ang ilalagay... pero bago ilagay ito.. siguraduhin nalagyan ito ng PVC cement/solvent para masecured ito at hindi kumalas...
6. Maglagay din ng glue using gluegun sa gilid ng pipe thread sa labas para mas secure din...
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
GEMINI96
PART III.
poking holes/butas butas butas
1. gumamit ng drill pambutas.. or mag-init ka nalang ng pako tapos ito nalang ang pambutas mo... or kung ano nalang ang trip mong pambutas..
*note: siguraduhin na ang ibang butas ay magkakasya ang mga rivet bullets dahil lalagyan ito ng rivet bullets para mas secured ang project natin..
2. sundan itong picture kung saan magbubutas.
http://i39.tinypic.com/2vnmk3k.jpg
3. poke two holes near the pipe thread.. having a gap of 3/4 inch
*dito mo ilalagay mamaya ang wires for igniter..
http://i39.tinypic.com/2j2erlu.jpg
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
GEMINI96
PART IV.
Securing the tincan, and the pipe thread using rivet bullets
1. kumuha ng rivet bullets at ang pang punch nito (rivet puncher)
2. lagyan ng rivet ang mga sumusunod..
http://i39.tinypic.com/2vnmk3k.jpg
http://i43.tinypic.com/2j0e9fp.jpg
http://i42.tinypic.com/aku8vr.jpg
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
GEMINI96
PART V.
preparing the igniter..
*kayo na po bahala kung gaano kahaba ang gusto nyo.. pero mas maganda kung maikli lang...
1. kumuha ng solid wires..
2. disasemble ang lpg lighter, tanggalin ang fluid container at kunin ang piezoelectric igniter sa loob ng LPG LIGHTER
3. strip the solid wires and connect it to the wire of the piezoelectric igniter
4. kumuha pa ng isang solid wire..
5. mag strip ka ng mga 3 or 4 inches nito..
6. ipaikot ito/ipalibot ito. sa may silver part ng piezoelectric igniter... *yung parang bakal sa bottom part.
7. i-test kung kumikislap ang dalawang wires pag pinindot mo ang piezoelectric igniter... (mga half inches mo ipagdikit ang wires)
8. pag okay na... ibalik ito sa loob ng lighter...
9. sa cover/casing ng lighter may makikita kang butas na maliit dun sa ibabang bahagi... doon mo ipalabas ang ginawa mong wires
http://i39.tinypic.com/2j2erlu.jpg
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED
Part VI.
ang pagdikit ng LPG lighter sa pvc pipe..
1. kumuha ng Gluegun at gluestick at isaksak ito sa outlet
2. idikit mo ang lpg lighter sa pipe.
*ikaw na bahala kung saan mo ilalagay..
3. lagyan mo ng glue ang palibot ng lighter.. wag lang sa part kung saan ito pinipindot..
4. lagyan ito ng cable zip tie para mas hindi umalog ang pipe...
5. yung dalawang wire na ginawa mo kanina.. ipasok ito sa dalawang butas na sinabi ko sa TUTORIAL PART III.
6. lagyan ng glue para hindi gumalaw...
http://i39.tinypic.com/2j2erlu.jpg
COPYING OF THIS THREAD WITHOUT PERMISSION IS PROHIBITED.
PART VII. **OPTIONAL OPTIONAL**
PIMPING PIMPING PIMPING YOUR BOGA
kayo na bahala dito...
sakin inspired by a cannon/heavy machine gun/gatling gun type na baril...
THAT'S ALL.
kung may katanungan pa kayo kindly reply to this or PM me nalang
willing ako tumulong sa mga gagawa nitong project ko..
Credits to Mang Paul.
yung manong na nagturo sakin kung papaano gumawa nito...
Ito ang aking finish Project
http://i44.tinypic.com/20b1yzq.jpg
POST NYO RIN PALA YUNG FINISHED PROJECT NYO!!!
Pasensya na kung medyo hindi malinaw ah...
ang cost pala ng project nito eh mga nasa 200 to 300 pesos.
P.P.S.
Para pala sa Spray/Bala... bumili kayo sa hardware ng DENATURED ALCOHOL..
WAG NA WAG PO KAYO GAGAMIT NG PAINT THINNER.. MEDYO MATAPANG KASI.
please don't quote this post..!!!