- Messages
- 115
- Reaction score
- 0
- Points
- 26
Hi kasymb.. Share ko lang prasa mga tamadBasta may tanong comment lang..
"Wag sana e-copy paste 2"., pagnagkaroon nito sa ibang FORUM... Alam na..Original made ko ito.. Hirap kung ginawa itong thread ko,"
Set-up Server for Cloning HDD via Network
Content:
Set IP Address.
Setting up of DHCP on Windows Server 2003.
Symantec Ghost Solution Suite Installation.
Creating VFD boot package.
Adding Entry to PXE Configuration Utility.
Creating and Restoring image of a PC and Dumping it to the Ghost Server.
Let's START
SET IP Address
SET IP ADDRESS First..
Go to Start> Control Panel> Network Connections> Local Area Connection. Click Properties then select Internet Protocol (TCP/IP) then Properties..
[/URL][/IMG]
[/URL][/IMG]
*Note: Need to Connect/Activate your Lan Connection First before to Start.
Step 1: Click Start>All Programs>Administrative Tools>Manage your Server
[/URL][/IMG]
Step 2: Click “Add or remove a role”
[/URL][/IMG]
Step 3: click “NEXT”
[/URL][/IMG]
Please wait
[/URL][/IMG]
Step 4: Select “Custom configuration” then click “Next”
[/URL][/IMG]
Step 5: Click “DHCP server” then click “Next”
[/URL][/IMG]
Step 6: Click “NEXT”
[/URL][/IMG]
Step 7: Click “NEXT”
[/URL][/IMG]
Step 8: Input Any Scope Name and Description and click “Next”
[/URL][/IMG]
Example:
Name: eyeteam
Description: lookup
Step 9: Define Scope of IP address range
[/URL][/IMG]
Step 10: Click NEXT “Add Exclusion”
[/URL][/IMG]
Step 11: Click NEXT “Lease Duration”
[/URL][/IMG]
Step 12: Select “No, I will configure these options later” then click “Next”
[/URL][/IMG]
Step 13: Click “Finish”
[/URL][/IMG]
Step 14: Successfully Setup DHCP server., Click “Finish”
[/URL][/IMG]
Step 15: Click “Manage this DHCP server”
[/URL][/IMG]
Step 16: Click “tingintinginserver (192.168.1.2)”
[/URL][/IMG]
Step 17: Click “Scope (192.168.1.0) tingintinginteam”
[/URL][/IMG]
Step 18: Click & Right Click “Scope Options” then Select Configure Options…
[/URL][/IMG]
Step 19: Click “003 Router” then input Starting IP address and click “Add” then click “OK”
[/URL][/IMG]
Tip: Kung ayaw mong mag conflic, Ung server gamitin mong IP ehh, 192.168.1.2 kung ayaw mo .2 eh d .100 or .200 tapos sa Starting IP mo nama 192.168.1.5
Step 20: Click “006 DNS Servers” then input Ending IP address and click “Add” then click “Apply”
[/URL][/IMG]
Step 21: click “015 DNS Domain Name” then Input ANY String Value Name then click “OK”
[/URL][/IMG]
Step 22: “FINISH” Close the DHCP
[/URL][/IMG]
[/URL][/IMG]
Check “PXE Server and “PowerCast Server” then click “Next”
[/URL][/IMG]
After installation of Symantec Ghost, Click “YES” to have PXE configured on DHCP.
[/URL][/IMG]
Click “FINISH”
[/URL][/IMG]
Success full installations…Click “OK”
[/URL][/IMG]
After installation Finish.. Restart the PC..
After Restarting PC, return to DHCP Server Settings to Check “060 ClassID” in Scope Options
[/URL][/IMG]
Click the Green Arrow to Activate Scope
[/URL][/IMG]
Scope Activated… FINISH… Close DHCP
[/URL][/IMG]
Step 1: Look of the “NDIS” of your PC
Step 2: Copy the Files of NDIS drivers to C:\Documents and Settings\AllUsers\ApplicationData\Symantec\Ghost\Templateor Download NDIS2 drivers from Manufacturer website.
Step 3: Click Start> All Programs> Symantec DeployCenter 5.7.0> DeployCenter 5.7.0 Tools> Boot Disk Builder
Step 4: Select “Standalone Boot Disks” then Click “Next”
Step 5: Select “Do not run ImageCenter” then click “Next
Step 6: Select “Virtual Boot Disk file” then click Ellipsis (…)
Step 7: Go to Location where you want to SAVE your VFD files.
Step 8: Ex. Select “Desktop” on dropdown and then write the name of the virtual floppy drive or .vfd
*Sample “LenovoSlim” then click “Open
Step 9: Click “Finish”
Step 10: Choose what you want (Optional).Select “Yes” if you want to save your settings or Select “No”
Step 11: Finish.. Click “Next” if you want to create another bootable disk or click “Exit” if you want to exit
Step 12: Creating Bootable Disk Successful
Step 13: Edit bootable disk that you created. Click Start> All Programs> Symantec DeployCenter 5.7.0> DeployCenter 5.7.0 Tools> VF Editor.
Step 13: Click “Open”
Step 14: Select your VFD file then click “Open”
Step 15: Delete this 2 files “pqdotask.bat” and “restrmbr.exe”
Step 16: Click “Image” then select “Change format…”
Step 17: Select “2.88 MB” then click “OK”
Step 18: Click “SAVE”
Step 19: Drag and drop out of VF Editor to the Desktop this files “autoexec.bat” and “config.sys” to edit..
Step 20: Open “Notepad”
Step 21: Drag and drop the “autoexec.bat” in the Notepad then delete all characters…
Step 22: Copy this format to your autoexec.bat then “SAVE” and Exit.
@echo off
SET TZ=GHO+08:00
prompt $p$g
\net\netbind.com
if exist MOUSE.COM MOUSE.COM
echo loading...
cd \ghost
echo loading...
GHOST.EXE
Step 23: Drag and drop the “config.sys” into Notepad to edit,.
Step 24: Copy this format to your “config.sys” then “SAVE” and Exit
DEVICE=\net\protman.dos /I:\net
DEVICE=\net\dis_pkt.dos
DEVICE=\net\B57.dos <---(Example of DOS Driver)
LASTDRIVE = Z
Step 25: After editing back the “autoexec.bat” and “config.sys” into VF Editor
Step 26: Click “All” or 2x “Yes” then “SAVE” and Minimize the VF Editor
Step 27: Create “2” New Folder into Desktop and name it to “ghost” and “net”
Step 28: Go to my computer> c:> Documents and settings> All users> Application Data> Symantec> Ghost> Templete> common then copy this 4 files “DIS_PKT.DOS”, “netbind.com”, “protman.dos”, "protman.exe”
Step 29: Paste the file in “net folder” you create on your desktop
Step 30: Open your “NDIS2 Driver” you download in “Step 1”then copy .DOS File (Example: B57.dos) and “PROTOCOL.INI”
Step 32: Open “NOTEPAD”
Step 33: Drag and drop the “PROTOCOL.INI” into “Notepad”
Step 34: Erase ALL Character's in your PROTOCOL.INI
Step 35: Copy this format to your “PROTOCOL.INI” then SAVE and Exit
[protman]
drivername=PROTMAN$
[pktdrv]
drivername=PKTDRV$
binding=nic
intvec=0x60
chainvec=0x60
[nic]
drivername=B57$ <---(Example of DOS Driver)
Step 36: Copy “ghost.exe” in MyComputer> ProgramFiles> Symantec> Ghost
Step 37: Paste to “ghost folder” you create in your desktop then Close
Step 38: Drag and drop?the?"Net" and "Ghost" sub-folders from your desktop?into?VF editor.
Step 39: Click “Yes”
Step 40: Click “SAVE” and Close the VF Editor
Step 1: Click on Start>ALL Programs>Symantec DeployCenter>DeployCenter Tools>PXE Configuration Utility
Step 2: Click “ADD” on PXE virtual floppies
Step 3: Click “…” (Ellipsis)
Step 4: Click dropdown list then select “Virtual Floppy(*.vfd)”
Step 5: Select your bootable disk (Exp. LenovoSlim.vfd) then Click “Open”
Step 6: Click “OK”
Step 7: Click “PXE client menu”
Step 8: Click “ADD”
Step 9: Input the PXE Client Name you want (Exp. LenovoSlim)
Step 10: Click dropdown then select “LenovoSlim.1”
Step 11: Click “OK”
Step 12: Click “EXIT”
Creating Image Files
Step 1: Go to Start> All Programs> Symantec Ghost>GhostCast Server”
Step 2: Creating Image Files.. Select “Create Image” then input ANY “Seassion Name” and then click “Browse”
Step 3: Input ANY Filename to your Image Files(Exp. LenovoSlim)
Step 4: Click “SAVE”
Step 5: Click “”Accept Clients”
Step 6: Waiting clients
Creating Source Image in progress…
Creating Complete...... FINISH……
Restoring Image Files..
Step 1: Select “Restore Image” then Input ANY “Session Name” and then click “Browse”
Step 2: Go to your Source ImageFiles location then click the Files then click “OK”
Step 3: Click “Accept Clients”
Step 4: Click “OK” *note: If you do not to see this reminder again CHECK [Don’t show this reminder again before Click OK
Step 5: Wait for clients to connect.
Yan haaaa... na update ko na... FINISH PROJECT... [email protected]
Set IP Address.
Setting up of DHCP on Windows Server 2003.
Symantec Ghost Solution Suite Installation.
Creating VFD boot package.
Adding Entry to PXE Configuration Utility.
Creating and Restoring image of a PC and Dumping it to the Ghost Server.
Let's START SET IP Address
SET IP ADDRESS First..
Go to Start> Control Panel> Network Connections> Local Area Connection. Click Properties then select Internet Protocol (TCP/IP) then Properties..
Setting up of DHCP on Windows Server 2003
*Note: Need to Connect/Activate your Lan Connection First before to Start.
Step 1: Click Start>All Programs>Administrative Tools>Manage your Server
Step 2: Click “Add or remove a role”
Step 3: click “NEXT”
Please wait
Step 4: Select “Custom configuration” then click “Next”
Step 5: Click “DHCP server” then click “Next”
Step 6: Click “NEXT”
Step 7: Click “NEXT”
Step 8: Input Any Scope Name and Description and click “Next”
Example:
Name: eyeteam
Description: lookup
Step 9: Define Scope of IP address range
Step 10: Click NEXT “Add Exclusion”
Step 11: Click NEXT “Lease Duration”
Step 12: Select “No, I will configure these options later” then click “Next”
Step 13: Click “Finish”
Step 14: Successfully Setup DHCP server., Click “Finish”
Step 15: Click “Manage this DHCP server”
Step 16: Click “tingintinginserver (192.168.1.2)”
Step 17: Click “Scope (192.168.1.0) tingintinginteam”
Step 18: Click & Right Click “Scope Options” then Select Configure Options…
Step 19: Click “003 Router” then input Starting IP address and click “Add” then click “OK”
Tip: Kung ayaw mong mag conflic, Ung server gamitin mong IP ehh, 192.168.1.2 kung ayaw mo .2 eh d .100 or .200 tapos sa Starting IP mo nama 192.168.1.5
Step 20: Click “006 DNS Servers” then input Ending IP address and click “Add” then click “Apply”
Step 21: click “015 DNS Domain Name” then Input ANY String Value Name then click “OK”
Step 22: “FINISH” Close the DHCP
Install Symantec Ghost Deploy Center
Check “PXE Server and “PowerCast Server” then click “Next”
After installation of Symantec Ghost, Click “YES” to have PXE configured on DHCP.
Click “FINISH”
Success full installations…Click “OK”
Install Symantec Ghost
After installation Finish.. Restart the PC..
After Restarting PC, return to DHCP Server Settings to Check “060 ClassID” in Scope Options
Click the Green Arrow to Activate Scope
Scope Activated… FINISH… Close DHCP
Create VFD boot package
Step 1: Look of the “NDIS” of your PC
Step 2: Copy the Files of NDIS drivers to C:\Documents and Settings\AllUsers\ApplicationData\Symantec\Ghost\Templateor Download NDIS2 drivers from Manufacturer website.
Step 3: Click Start> All Programs> Symantec DeployCenter 5.7.0> DeployCenter 5.7.0 Tools> Boot Disk Builder
Step 4: Select “Standalone Boot Disks” then Click “Next”
Step 5: Select “Do not run ImageCenter” then click “Next
Step 6: Select “Virtual Boot Disk file” then click Ellipsis (…)
Step 7: Go to Location where you want to SAVE your VFD files.
Step 8: Ex. Select “Desktop” on dropdown and then write the name of the virtual floppy drive or .vfd
*Sample “LenovoSlim” then click “Open
Step 9: Click “Finish”
Step 10: Choose what you want (Optional).Select “Yes” if you want to save your settings or Select “No”
Step 11: Finish.. Click “Next” if you want to create another bootable disk or click “Exit” if you want to exit
Step 12: Creating Bootable Disk Successful
Step 13: Edit bootable disk that you created. Click Start> All Programs> Symantec DeployCenter 5.7.0> DeployCenter 5.7.0 Tools> VF Editor.
Step 13: Click “Open”
Step 14: Select your VFD file then click “Open”
Step 15: Delete this 2 files “pqdotask.bat” and “restrmbr.exe”
Step 16: Click “Image” then select “Change format…”
Step 17: Select “2.88 MB” then click “OK”
Step 18: Click “SAVE”
Step 19: Drag and drop out of VF Editor to the Desktop this files “autoexec.bat” and “config.sys” to edit..
Step 20: Open “Notepad”
Step 21: Drag and drop the “autoexec.bat” in the Notepad then delete all characters…
Step 22: Copy this format to your autoexec.bat then “SAVE” and Exit.
@echo off
SET TZ=GHO+08:00
prompt $p$g
\net\netbind.com
if exist MOUSE.COM MOUSE.COM
echo loading...
cd \ghost
echo loading...
GHOST.EXE
Step 23: Drag and drop the “config.sys” into Notepad to edit,.
Step 24: Copy this format to your “config.sys” then “SAVE” and Exit
DEVICE=\net\protman.dos /I:\net
DEVICE=\net\dis_pkt.dos
DEVICE=\net\B57.dos <---(Example of DOS Driver)
LASTDRIVE = Z
Step 25: After editing back the “autoexec.bat” and “config.sys” into VF Editor
Step 26: Click “All” or 2x “Yes” then “SAVE” and Minimize the VF Editor
Step 27: Create “2” New Folder into Desktop and name it to “ghost” and “net”
Step 28: Go to my computer> c:> Documents and settings> All users> Application Data> Symantec> Ghost> Templete> common then copy this 4 files “DIS_PKT.DOS”, “netbind.com”, “protman.dos”, "protman.exe”
Step 29: Paste the file in “net folder” you create on your desktop
Step 30: Open your “NDIS2 Driver” you download in “Step 1”then copy .DOS File (Example: B57.dos) and “PROTOCOL.INI”
Step 32: Open “NOTEPAD”
Step 33: Drag and drop the “PROTOCOL.INI” into “Notepad”
Step 34: Erase ALL Character's in your PROTOCOL.INI
Step 35: Copy this format to your “PROTOCOL.INI” then SAVE and Exit
[protman]
drivername=PROTMAN$
[pktdrv]
drivername=PKTDRV$
binding=nic
intvec=0x60
chainvec=0x60
[nic]
drivername=B57$ <---(Example of DOS Driver)
Step 36: Copy “ghost.exe” in MyComputer> ProgramFiles> Symantec> Ghost
Step 37: Paste to “ghost folder” you create in your desktop then Close
Step 38: Drag and drop?the?"Net" and "Ghost" sub-folders from your desktop?into?VF editor.
Step 39: Click “Yes”
Step 40: Click “SAVE” and Close the VF Editor
Adding Entry to PXE Configuration Utility
Step 1: Click on Start>ALL Programs>Symantec DeployCenter>DeployCenter Tools>PXE Configuration Utility
Step 2: Click “ADD” on PXE virtual floppies
Step 3: Click “…” (Ellipsis)
Step 4: Click dropdown list then select “Virtual Floppy(*.vfd)”
Step 5: Select your bootable disk (Exp. LenovoSlim.vfd) then Click “Open”
Step 6: Click “OK”
Step 7: Click “PXE client menu”
Step 8: Click “ADD”
Step 9: Input the PXE Client Name you want (Exp. LenovoSlim)
Step 10: Click dropdown then select “LenovoSlim.1”
Step 11: Click “OK”
Step 12: Click “EXIT”
Creating and Restoring ImageusingGhostCast Server
Creating Image Files
Step 1: Go to Start> All Programs> Symantec Ghost>GhostCast Server”
Step 2: Creating Image Files.. Select “Create Image” then input ANY “Seassion Name” and then click “Browse”
Step 3: Input ANY Filename to your Image Files(Exp. LenovoSlim)
Step 4: Click “SAVE”
Step 5: Click “”Accept Clients”
Step 6: Waiting clients
Creating Source Image in progress…
Creating Complete...... FINISH……
Restoring Image Files..
Step 1: Select “Restore Image” then Input ANY “Session Name” and then click “Browse”
Step 2: Go to your Source ImageFiles location then click the Files then click “OK”
Step 3: Click “Accept Clients”
Step 4: Click “OK” *note: If you do not to see this reminder again CHECK [Don’t show this reminder again before Click OK
Step 5: Wait for clients to connect.
Yan haaaa... na update ko na... FINISH PROJECT... [email protected]
Last edited:
haha but anyway nice work! keep on sharing! 
