GPU driver installed > Windows logo > No signal

[Kaireen]

Processor - Intel Core i5-3470 Processor
Motherboard - Intel® H61 Jetway 1155
PSU - TruRated 600w Greatwall
RAM - 8GB 1333
Hard Drive - 500GB HDD
Graphics Card - AMD Radeon R9 290x
Monitor - 22" widescreen LED 60 mhz
Operating System - Windows 7 ROG

- after installing GPU driver and restart PC "Windows logo > No signal"

- after reformat PC

- I’ve been having this issue for a little while after I installed my GPU [R9 290x] driver it will show the bios screen and then windows logo after it goes to no signal[monitor]. I went to safe mode by pressing F8 I can go through after the windows logo. I tried to uninstall and install the latest driver of my GPU. Issue still occurs, I tried my old GPU [GTX 660] everything is working fine. Do I have to consider my GPU [R9 290x] unuseable? or someone help me troubleshoot my issue with my GPU.

 

[taurexn]

ano gamit mong power supply, baka kulang yun power kasi malakas sa wattage yan amd card unlike sa nvidia card.... parang hindi nya kayang paganahin... double check mo kung naikabit mo yun 6-pin power sa card.... or try mo gumamit ng high wattage na psu

 

[cloneako]

sir ano brand ng monitor mo? if acer, try mo mag palit ng monitor. nang yari na sakin yan.. nanghiram lang ako ng monitor tapus inadajust ko yung resolution, para mag fit sa resolution ng acer monitor ko..

 

[Kaireen]

Re: GPU driver installed > Windows logo > No signal

- - - Updated - - -

sir ano brand ng monitor mo? if acer, try mo mag palit ng monitor. nang yari na sakin yan.. nanghiram lang ako ng monitor tapus inadajust ko yung resolution, para mag fit sa resolution ng acer monitor ko..

patay acer nga.. :O try ko po to ung ginawa mo salamat po!!

- - - Updated - - -

ano gamit mong power supply, baka kulang yun power kasi malakas sa wattage yan amd card unlike sa nvidia card.... parang hindi nya kayang paganahin... double check mo kung naikabit mo yun 6-pin power sa card.... or try mo gumamit ng high wattage na psu

TruRated 600w Greatwall ito po ung PSU gamit ko. actually boss, gumagana na po to dati pero inireformat ko ung PC ko ito ung nangyari.

 

[damnskaterboi]

EVENT VIEWER
tignan mo ddon kung saan may mali
sabi mo lumalagpas siya ng BIOS, so walang problema sa HARDWARE
kaso after WINDOWS LOGO doon na nagloloko so possible SOFTWARE
tsaka walang problema kapag nasa safemode ka.

make sure lang na yung GPU na iniinstall mo is pang Win7 not for WIN10. SAbi ko kasi later version ng GPU ang iniinstall mo eh

 

[themonyo]

duda ko pinipilit ng video card run mo yung monitor sa higher than 60hz yung refresh rate pero di supported ng monitor mo
kung makakapasok ka ng safe mode, punta ka sa Display Settings > Advance Display Settings > Display adapter properties for display 1
tapos punta ka sa Monitor Tab
di ko matandaan yung sa windows 7 pero parang ganyan din
tignan mo sa Monitor Settings yung Screen refresh rate:
try mo palitan to 60 Hertz tapos restart PC mo at subukan kung gagana nga. meron din setting nyan sa Radeon Driver pero di ko matandaan kung saan banda kasi ilang taon na rin ako walang Radeon GPU. pwede mo burahin yung resolution with higher frequencies than 60hz para sa monitor mo na yun. wala naman issue kung magpapalit ka ng monitor kasi madedetect ng driver na bago na monitor mo kaya magse-set na naman sya ng bagong profile para doon.
pwede ka rin gumamit ng CRU na software para burahin yung higher display frequency para hindi na sya pilitin na lumagpas ng 60hz.