B315s Restoration from soft-brick (Fully Restore)

[UnknownBot]

21.311.03 Polkomtel na xa now Sir, nag Flash aq Gamit yung Multicast ni Sir Jansen Ramos pero waley pa rin still No Signal, di Ko sure kung success ba aq dito sa tut mo kc eto talaga unang ginawa ko nung Nag red tide/No Service C 936 ko, wala kc lumabas na OK dun sa cmd yung delete NVRAM ba yun, tinuloy ko yung Upgrade gamit yung Updater success naman pero d pa rin nya naayos ang NO Service Problem..Pa help naman po

View attachment 1214461 View attachment 1214462

hindi nadedetect ng pc mo yung adb ng modem mo. maginstall ka drivers.

 

[cornmae12]

21.311.03 Polkomtel na xa now Sir, nag Flash aq Gamit yung Multicast ni Sir Jansen Ramos pero waley pa rin still No Signal, di Ko sure kung success ba aq dito sa tut mo kc eto talaga unang ginawa ko nung Nag red tide/No Service C 936 ko, wala kc lumabas na OK dun sa cmd yung delete NVRAM ba yun, tinuloy ko yung Upgrade gamit yung Updater success naman pero d pa rin nya naayos ang NO Service Problem..Pa help naman po

View attachment 1214461 View attachment 1214462

same tayo prob sir... need pa antenna para mag 4g.. no service naman kung built in antenna lang..
anu kaya solusyon?? sabi ni jansen daw un sa tutorial nya.. ginawa ko na din ung multicast.. ganun pa dn.

 

[argiemateo]

ts ask ko lng of kailangan pa microsoft netframework sa windows 7/ 32? tnx in advance...

 

[kevin0152]

21.311.03 Polkomtel na xa now Sir, nag Flash aq Gamit yung Multicast ni Sir Jansen Ramos pero waley pa rin still No Signal, di Ko sure kung success ba aq dito sa tut mo kc eto talaga unang ginawa ko nung Nag red tide/No Service C 936 ko, wala kc lumabas na OK dun sa cmd yung delete NVRAM ba yun, tinuloy ko yung Upgrade gamit yung Updater success naman pero d pa rin nya naayos ang NO Service Problem..Pa help naman po

View attachment 1214461 View attachment 1214462

bakit nag multicast kapa alam ko may bug yung kay jansen try mo ulitin tut sa 1st page make susre deleted directory etc tapos wag multicast try mo eh upload sa browser mismo try mo evo+ naman

 

[janex91]

same tayo prob sir... need pa antenna para mag 4g.. no service naman kung built in antenna lang..
anu kaya solusyon?? sabi ni jansen daw un sa tutorial nya.. ginawa ko na din ung multicast.. ganun pa dn.

Medyu nagkakaroon na nag Pag-asa yung saken Sir, nakapag ADB fastboot commands na aq gamit yung commitblocks.cmd , effective kc no Need na pag Pindot WPS+Power pra maka pag USB Mode/Fastboot, na delete ko na nvram image at success yng Ibang fastboot commands, nag kokonek na xa sa 3G di gaya dati na hanggang 2G lang , pero pag tinanggal ko antena- pa pitik2x lang yung signal pa wala2x ang 3g ..pero pag Ni-lock ko sa 4G- No Service pa rin kahit may Antena..Malakas naman Globe LTE dito.Sana sa FW lang..try ko magpalit ng FW , Pwede ba i local update from Polkomtel 21.311.03 to Latest 21.316.01.00.69 via GUI?

View attachment 321017 View attachment 321018 View attachment 321019

 

[ronafeb]

Fully Restore your soft-bricked modem with this tutorial. (from No Service to Power LED Only problem)
A complete niggy (newbie) guide by reimu. (actually i just ripped this from russian gsm? forum 4pda, and translated it.)

Download the files here.

[CENTER]https://mega.nz/#!HlkWmBoB!H_8tBG_P5vn_f_k3GemPW3e17BG7SuoCD93eG-A7-N8
https://www.mediafire.com/?8w0nnayu89wx46e
Password : Gensokyo$!!reimu[/CENTER]

Question :

Can I change to any firmwares available in this forum?
a : Yes you can, currently using mine with modified 21.321.03.01.973 Firmware installed.

Prerequisites :
Metal conductor for jumping BOOT and GND pin on the board.
Files required for doing this tutorial. (Firmware, balong_flash, and usbdloader.bin)

Procedure :

Contact BOOT and GND pin, and then plug the Power Adapter to the modem. If the Power Light lit after connecting the Power Supply, repeat the steps. If not, then proceed to the next step.
View attachment 1210092
Reference Picture of BOOT pin.

Connect USB Male to Male Cable to the Modem and to your Computer, It should show a COM PORT of HUAWEI Mobile Connect - 3G PC UI Interface.

Run commitblocks.cmd, and select option number 1.

Fastboot should respond to the Command Prompt with "OK" status, if it respond with a "FAIL" status. Repeat the steps.

After deleting nvram image of your modem, turn it off then repeat the first step above for jumping BOOT and GND pins.

Once you get to work the BOOT and GND pin again and it shows a HUAWEI Mobile Connect - 3G PC UI Interface COM PORT at Device Manager.

Run load_usbdloader.cmd. The script will automatically load usbdloader to the modem, once finished it will show a new COM PORT named HUAWEI Mobile Connect - 3G Application Interface on Device Manager.

Run B315s-22_Update_21.311.05.00.00_M_01.01_nvr.exe and click Start. When the Firmware Upgrader Program found the COM PORT of your device, device LED lights will lit up. Wait until the Firmware Upgrader completes downloading the software to your modem, and also wait for the modem to reboot itself.

Once you finish flashing the firmware to your modem, unplug the USB Male to Male cable then do a power cycle to your device (Unplug and replug the power adapter)

Plug LAN Cable to your modem and go to 192.168.8.1, if a Generic WEBUI of Huawei shows up. Congratulations, you've just successfully revived your modem from "death".

Thanks to rust3028 of 4pda.ru for the files.
View attachment 1210088

​

sa wakas na ayos ko din modem q....
Tnxs tnxs tnxs.... galing galing galing

 

[kevin0152]

sa wakas na ayos ko din modem q....
Tnxs tnxs tnxs.... galing galing galing

sa mga naayos ang modem mas ok if specify sana mga symptoms ng sira ng modem anu problema at anu mga natry before itong tut na ito

 

[reynant]

bakit nag multicast kapa alam ko may bug yung kay jansen try mo ulitin tut sa 1st page make susre deleted directory etc tapos wag multicast try mo eh upload sa browser mismo try mo evo+ naman

Sir ibig sabihin yung 1st at 2nd command lang ung gagawin??hindi na yung firmware upgrader??tpos sa web na lang mag update??gusto ko kasi ma try yung evo+ na firmware..salamat

 

[janex91]

Sir ibig sabihin yung 1st at 2nd command lang ung gagawin??hindi na yung firmware upgrader??tpos sa web na lang mag update??gusto ko kasi ma try yung evo+ na firmware..salamat

Anu ba FW gamit mo ? Yung Firmware upgrade bale Middle East yung FW nun, pag gusto mo mag change FW /upgrade ka to Evo+, dun ka lang sa browser/GUI mag Local Update browse mo lang yun bin file ng Evo + tapos wait mo lang mag Reboot ang MOdem

 

[reynant]

Anu ba FW gamit mo ? Yung Firmware upgrade bale Middle East yung FW nun, pag gusto mo mag change FW /upgrade ka to Evo+, dun ka lang sa browser/GUI mag Local Update browse mo lang yun bin file ng Evo + tapos wait mo lang mag Reboot ang MOdem

21.311.05.00.00 yan po gamit ko fw sir..

 

[janex91]

21.311.05.00.00 yan po gamit ko fw sir..

pwede yan Local Update para maging Evo+ .click Update tab>Local Update -Choose Bin File wait mo lang , Observe mo lang yung behavior ng Lights kung nag reboot na wait mo pa ilang Minutes pra sure , then Ok na yan

 

[markshiatle]

Di ko alam if effective ba sya sa 936 ko, kasi before red mode lagi sya,,

No apn before ko ma-flash,, nagawa ko success naman kaso di pa rin maka add ng apn,, pero blue-green (LTE) na ung modem ko,,

 

[reynant]

pwede yan Local Update para maging Evo+ .click Update tab>Local Update -Choose Bin File wait mo lang , Observe mo lang yung behavior ng Lights kung nag reboot na wait mo pa ilang Minutes pra sure , then Ok na yan

Ok na sir..nag multicast na lang ako para makapag update evo+..Lagi kasi failed pag local update..

 

[kevin0152]

Ok na sir..nag multicast na lang ako para makapag update evo+..Lagi kasi failed pag local update..

actually pag yung tut lang na ito ginawa saka applicable yung via local update if yung provided na firmware ni ts ang ginamit niyo
for restoration

pero if like for example kay jansen etc ang ginamit niyo na firmware hindi pwede local update without doing some extra steps

 

[reynant]

May bug siguro yung luma firmware ni polko..kasi 2 modem ko naging power led only(old 936 ska blue label)halos magkasabay pa..buti na buhay ko gamit tutorial ni ts..salamat ulit ng marami..

 

[romanocruz34]

Fully Restore your soft-bricked modem with this tutorial. (from No Service to Power LED Only problem)
A complete niggy (newbie) guide by reimu. (actually i just ripped this from russian gsm? forum 4pda, and translated it.)

Download the files here.

[CENTER]https://mega.nz/#!HlkWmBoB!H_8tBG_P5vn_f_k3GemPW3e17BG7SuoCD93eG-A7-N8
https://www.mediafire.com/?8w0nnayu89wx46e
Password : Gensokyo$!!reimu[/CENTER]

Question :

Can I change to any firmwares available in this forum?
a : Yes you can, currently using mine with modified 21.321.03.01.973 Firmware installed.

Prerequisites :
Metal conductor for jumping BOOT and GND pin on the board.
Files required for doing this tutorial. (Firmware, balong_flash, and usbdloader.bin)

Procedure :

Contact BOOT and GND pin, and then plug the Power Adapter to the modem. If the Power Light lit after connecting the Power Supply, repeat the steps. If not, then proceed to the next step.
View attachment 1210092
Reference Picture of BOOT pin.

Connect USB Male to Male Cable to the Modem and to your Computer, It should show a COM PORT of HUAWEI Mobile Connect - 3G PC UI Interface.

Run commitblocks.cmd, and select option number 1.

Fastboot should respond to the Command Prompt with "OK" status, if it respond with a "FAIL" status. Repeat the steps.

After deleting nvram image of your modem, turn it off then repeat the first step above for jumping BOOT and GND pins.

Once you get to work the BOOT and GND pin again and it shows a HUAWEI Mobile Connect - 3G PC UI Interface COM PORT at Device Manager.

Run load_usbdloader.cmd. The script will automatically load usbdloader to the modem, once finished it will show a new COM PORT named HUAWEI Mobile Connect - 3G Application Interface on Device Manager.

Run B315s-22_Update_21.311.05.00.00_M_01.01_nvr.exe and click Start. When the Firmware Upgrader Program found the COM PORT of your device, device LED lights will lit up. Wait until the Firmware Upgrader completes downloading the software to your modem, and also wait for the modem to reboot itself.

Once you finish flashing the firmware to your modem, unplug the USB Male to Male cable then do a power cycle to your device (Unplug and replug the power adapter)

Plug LAN Cable to your modem and go to 192.168.8.1, if a Generic WEBUI of Huawei shows up. Congratulations, you've just successfully revived your modem from "death".

Thanks to rust3028 of 4pda.ru for the files.
View attachment 1210088

​

Not working on me.

 

[greenartifacts]

stock po ako sa waiting device. help

 

[daryl_rasta]

naka 5 blue label na ako nito,.
sa dami ng tut nagsilabasan ito ang tested sa akin
salamat TS

- - - Updated - - -

 

[UnknownBot]

Di ko na problema yan kung hindi nagana o hindi niyo mapagana sa inyo. Basta sa amin naman ok yan.

 

[babytv]

mga master paano po pag "USB Device not recognized"